Every RVer needs to understand the importance of tires and proper tire pressure. The problem that can sometimes occur is while on the road, there is no available air support to check tire pressure. If you wait until you're on the road to check tire pressure, the tires are too hot for correct evaluation.
This is a common problem for RVers, and that is why you might want to consider a portable air compressor. Here are a few pointers when deciding what compressor to purchase: The rate that a compressor can deliver a volume of air is measured in cubic feet per minute (cfm). cfm varies with atmospheric pressure. It also varies with the temperature and humidity of the air.
Technically, air compressor manufacturers calculate standard cubic feet per minute (scfm) as cfm at sea level with 68 degrees F air at 36% relative humidity. Scfm ratings are given at a specific pressure (for example) 3.0 scfm at 90 psi. If you reduce pressure, scfm goes up, and vice versa. I would recommend a model rated at about 4.9 cfm @90 psi The cfm and psi ratings are important because they will determine what a compressor is capable of doing.
The most important thing to determine when choosing a compressor is to make sure it can supply the amount of air and the pressure that your tires need. Many applications in garages and shops (like air tools) don't require 125 max psi, so they have a regulator to adjust the air. It may be necessary to increase this setting to inflate the tires.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
Wednesday, December 31, 2008
Wednesday, December 17, 2008
What's best, gas or diesel engine?
Dear Mark,
I sold my 24' Class C motorhome and am shopping for something newer and more efficient, also larger. I'm tending toward the Class B+ Phoenix Cruiser, 27' with two slides. It comes as either gasoline or diesel. I've been told the additional cost for a diesel engine outweighs any gas mileage benefit unless you keep the rig for many years. But I also wonder if other things have been factored in, such as, cost of engine maintenance, cost differential for the fuel type (as gasoline prices rise, will diesel rise at the same rate, slower, faster? What about bio diesel? Is there a re-sale advantage to either one?
I haven't found a discussion of these issues anywhere yet. The dealer I've been working with just gave me the answer above... the diesel is not cost-effective unless kept for many years. I'm an older, single woman, wanting to do some touring with my dog for the next two years or so. I'm expecting various friends to link up for certain legs of the trip. I will appreciate good guidance.
Mark says:
Gas versus diesel is an age old discussion and one that often times gets heated. If asked this question several years ago I would have responded similar to the salesperson because the cost of a diesel model over a gas model was quite significant. Today's RV's offer many gasoline models in the same price range as many diesel products, mainly due to advances in the chassis itself driving the prices upward.
What I can tell you is a diesel will last longer than a gasoline engine so if you plan to keep the RV for a long time it would be worth the investment. I have no idea what is going to happen with the types of fuel or the cost difference between gas and diesel.
Maintenance wise, it used to be that a diesel required less, keeping in mind there are more filters, etc., on a diesel. But nowadays gas engines can go upwards of 100,000 miles before a tune up with nothing more than routine oil changes, air filters, etc.
This probably doesn't help much. If you want some other opinions, I recommend you go to the RVtravel.com forum and post this same question in the appropriate forum. You are sure to get many responses.
I sold my 24' Class C motorhome and am shopping for something newer and more efficient, also larger. I'm tending toward the Class B+ Phoenix Cruiser, 27' with two slides. It comes as either gasoline or diesel. I've been told the additional cost for a diesel engine outweighs any gas mileage benefit unless you keep the rig for many years. But I also wonder if other things have been factored in, such as, cost of engine maintenance, cost differential for the fuel type (as gasoline prices rise, will diesel rise at the same rate, slower, faster? What about bio diesel? Is there a re-sale advantage to either one?
I haven't found a discussion of these issues anywhere yet. The dealer I've been working with just gave me the answer above... the diesel is not cost-effective unless kept for many years. I'm an older, single woman, wanting to do some touring with my dog for the next two years or so. I'm expecting various friends to link up for certain legs of the trip. I will appreciate good guidance.
Mark says:
Gas versus diesel is an age old discussion and one that often times gets heated. If asked this question several years ago I would have responded similar to the salesperson because the cost of a diesel model over a gas model was quite significant. Today's RV's offer many gasoline models in the same price range as many diesel products, mainly due to advances in the chassis itself driving the prices upward.
What I can tell you is a diesel will last longer than a gasoline engine so if you plan to keep the RV for a long time it would be worth the investment. I have no idea what is going to happen with the types of fuel or the cost difference between gas and diesel.
Maintenance wise, it used to be that a diesel required less, keeping in mind there are more filters, etc., on a diesel. But nowadays gas engines can go upwards of 100,000 miles before a tune up with nothing more than routine oil changes, air filters, etc.
This probably doesn't help much. If you want some other opinions, I recommend you go to the RVtravel.com forum and post this same question in the appropriate forum. You are sure to get many responses.
Thursday, November 27, 2008
This travel companion can keep you sane, save your marriage
What weighs 15 ounces; is the size of a deck of cards and could possibly save an RVer's marriage? Let me give you a scenario. You’re driving your 35-foot RV on a congested four lane highway during rush hour, somewhere you've never been before and your better half is your navigator. You miss your exit and now you need to go 25 miles out of your way to get back on the correct route, arguing about whose fault it was the whole time. Sound familiar?
Now, let’s see what we can do to fix this problem. You’re driving your RV on a congested four lane highway, during rush hour, somewhere you have never been before and your new Global Positioning System (GPS) is your navigator. The unique, turn-by-turn, voice prompt feature instructs you to turn right in eight tenths of a mile. You don’t miss your exit; you don’t need to go 25 miles out of your way and your marriage remains intact.
In the past, whenever my wife Dawn and I would take a trip in the RV, I would print the driving directions from a trip planning website. Then, as we traveled, she would inform me of when and where we would make any changes in our route. Needless to say we missed turns, took wrong exits and on more than one occasion there were those last second, white knuckle lane changes: if you’ve been RVing for a while you know what I’m talking about.
I FINALLY DECIDED to take advantage of modern day technology and purchase a GPS system. All I can say is I should kick myself for waiting so long to do it. The more I learned about these GPS systems the more fascinated I was with their capabilities. Most come pre-programmed with detailed maps, automatic trip routing, voice-prompted turn-by-turn directions along your route, and easy-to-follow touch screen displays, which is exactly what you want when you’re traveling in an RV. If you get a text-to-speech feature the GPS actually calls out the turns you need to make, so you can keep your eyes where they need to be, on the road. If you miss a turn the GPS system automatically recalculates the quickest way to get back on the correct route.
Other features we liked about the GPS are the Points of Interest (POI) like, restaurants, shopping centers and tourist attractions. In addition to all of these features the GPS model we purchased includes a built in MP3 player and a JPEG picture viewer too.
I don’t know about you, but driving an RV in places you've never been before can be nerve-racking at times, especially if you're navigating the old school way, using a map. I am sometimes a little slow to change to the latest technology, but getting a GPS system to help navigate the RV is the best thing I’ve done since switching from dial-up to high speed internet service. This truly is a great way to make traveling in your RV less stressful. And, who knows, it might just result in a happier marriage, too!
A final note: I still print the route from a trip planning website and keep my maps next to the drivers seat, just in case!
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
Now, let’s see what we can do to fix this problem. You’re driving your RV on a congested four lane highway, during rush hour, somewhere you have never been before and your new Global Positioning System (GPS) is your navigator. The unique, turn-by-turn, voice prompt feature instructs you to turn right in eight tenths of a mile. You don’t miss your exit; you don’t need to go 25 miles out of your way and your marriage remains intact.
In the past, whenever my wife Dawn and I would take a trip in the RV, I would print the driving directions from a trip planning website. Then, as we traveled, she would inform me of when and where we would make any changes in our route. Needless to say we missed turns, took wrong exits and on more than one occasion there were those last second, white knuckle lane changes: if you’ve been RVing for a while you know what I’m talking about.
I FINALLY DECIDED to take advantage of modern day technology and purchase a GPS system. All I can say is I should kick myself for waiting so long to do it. The more I learned about these GPS systems the more fascinated I was with their capabilities. Most come pre-programmed with detailed maps, automatic trip routing, voice-prompted turn-by-turn directions along your route, and easy-to-follow touch screen displays, which is exactly what you want when you’re traveling in an RV. If you get a text-to-speech feature the GPS actually calls out the turns you need to make, so you can keep your eyes where they need to be, on the road. If you miss a turn the GPS system automatically recalculates the quickest way to get back on the correct route.
Other features we liked about the GPS are the Points of Interest (POI) like, restaurants, shopping centers and tourist attractions. In addition to all of these features the GPS model we purchased includes a built in MP3 player and a JPEG picture viewer too.
I don’t know about you, but driving an RV in places you've never been before can be nerve-racking at times, especially if you're navigating the old school way, using a map. I am sometimes a little slow to change to the latest technology, but getting a GPS system to help navigate the RV is the best thing I’ve done since switching from dial-up to high speed internet service. This truly is a great way to make traveling in your RV less stressful. And, who knows, it might just result in a happier marriage, too!
A final note: I still print the route from a trip planning website and keep my maps next to the drivers seat, just in case!
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
Tuesday, November 18, 2008
Must RV's electrical converter be on at all times?
Dear Mark,
I live year round in a large 5th wheel trailer and I am plugged in at all times. I hear the battery charger kicking in from time to time and the humming of the converter. Do I need to have the converter on at all times? Is it on only to charge the batteries? The manuals are the pits and I am really trying to know all about converters. The more questions I ask from different sources the more answers I get.
Mark:
The converter in your RV basically does two jobs.
1) When you are plugged into electricity it converts a portion of the 120 volts coming into the RV down to 12 volts so all of the 12 volt devices like overhead lights and fan motors will operate without draining the RV battery.
2) It has a battery charger built in the converter to keep the RV battery charged (topped off).
The noise you are hearing is most likely the fan on the converter. The converter gets warm when it is on so the manufacturer adds a fan to help keep it cool. Some are very noisy. You DO NEED the converter on when you are plugged in. If the converter wasn't on, or wasn't operating properly you would run the RV battery down because you are using the 12-volt appliances and devices.
Some older RV converters charge the batteries at a constant rate and will continue to charge the batteries when they are fully charged. This can result in the battery or batteries losing water, so battery maintenance and inspections are important when you have the RV plugged in for long periods of time. Newer converters have three stage chargers that know when the battery is fully charged and at that point only provide a float charge (less charge) to prevent overcharging conditions.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
I live year round in a large 5th wheel trailer and I am plugged in at all times. I hear the battery charger kicking in from time to time and the humming of the converter. Do I need to have the converter on at all times? Is it on only to charge the batteries? The manuals are the pits and I am really trying to know all about converters. The more questions I ask from different sources the more answers I get.
Mark:
The converter in your RV basically does two jobs.
1) When you are plugged into electricity it converts a portion of the 120 volts coming into the RV down to 12 volts so all of the 12 volt devices like overhead lights and fan motors will operate without draining the RV battery.
2) It has a battery charger built in the converter to keep the RV battery charged (topped off).
The noise you are hearing is most likely the fan on the converter. The converter gets warm when it is on so the manufacturer adds a fan to help keep it cool. Some are very noisy. You DO NEED the converter on when you are plugged in. If the converter wasn't on, or wasn't operating properly you would run the RV battery down because you are using the 12-volt appliances and devices.
Some older RV converters charge the batteries at a constant rate and will continue to charge the batteries when they are fully charged. This can result in the battery or batteries losing water, so battery maintenance and inspections are important when you have the RV plugged in for long periods of time. Newer converters have three stage chargers that know when the battery is fully charged and at that point only provide a float charge (less charge) to prevent overcharging conditions.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
Thursday, November 6, 2008
How to troubleshoot problems with your RV's 12-volt system
If you've been RVing for any amount of time you already know that a most of the devices and accessories in your motorhome, trailer or other RV operates on 12-volt DC power. Twelve-volt DC (or direct current) is supplied by the RV batteries. DC electricity flows in one direction, from negative to positive. Twelve-VDC electricity is stored in the RV batteries and supplies power for components, devices and appliances that operate on 12-volts.
These devices include overhead lights, the water pump, vent fans, furnace fan, range hood fan, LP gas leak detectors, stereos, 12-volt TVs and the refrigerator when it's operating in the LP gas mode. When camping you rely on these 12-volt items to operate properly, especially if you're dry camping without hook-ups. So what do you do when one of these 12-volt items quit working?
For the sake of an example let's say that we are dry camping and our 12-volt water pump quits working.
I am convinced that just about anybody is capable of troubleshooting a 12-VDC problem, and in many cases repairing the problem without it ruining a camping trip. For starters you'll need a couple of simple tools to assist you in troubleshooting your RV’s 12-volt electrical system.
1). An inexpensive 12-volt test light.
2). A multi-meter that can test for DC power.
Both of these are available at local auto parts stores. You should also keep some electrical tape, various size wire nuts, 12-volt light bulbs and 12-volt fuses on hand. Check the amperage of the fuses used in the power distribution box and keep an assortment. If you're aware of any inline fuses used on any of the 12-volt devices keep these on hand too.
Now, try to determine the last time the water pump actually worked. Did you leave the RV for a period of time with the pump on? Is there water in the fresh water holding tank? Were you working on or around something else that could have affected the operation of the water pump? Try to think of all possible scenarios. Something might jar your memory resulting in a quick fix to the problem.
If not, the first step is to verify that the coach battery or batteries are charged enough to supply power to these 12-volt items. There are a couple of ways to perform a quick test on the coach batteries. You can use the monitor panel to check their condition. For an accurate reading, make sure the RV is not plugged into electricity and turn on a couple of overhead lights to place a small load on the battery. Check the reading at the monitor panel. (If you check the reading at the monitor panel when the RV is plugged in to electricity it will give you fully charged reading) A more accurate method is to test the battery with a multi-meter. Set the meter to read 12-VDC and place the negative test probe on the negative battery terminal and the positive test probe on the positive battery terminal. A fully charged battery will read in the range of 12.6 to 12.7 volts. If it reads less than 12-volts it is below a 50 percent state of charge and will need to be charged.
IF THE BATTERY IS FULLY CHARGED, the next step is to make sure that any battery disconnect switch for the coach battery is turned on. If the battery disconnect switch is on, verify that other 12-volt devices in the RV are operating properly. If there is 12-volt power to the interior of the RV you need to check the fuse for the water pump in the power distribution center. Determine which fuse is for the water pump (fuses are normally labeled) and find a suitable ground for the 12-volt test light. Test both sides of the fuse for 12-volt power. If the test light only lights on one side of the fuse replace it with the proper size fuse and try the water pump again. If there was power at both sides of the fuse check for 12-volts at the water pump switch. If there is voltage, and the switch is operating properly check the water pump wiring for an inline fuse.
Find a good ground for the 12-volt test light and probe the wire on both sides of the fuse. If there is only power on one side of the fuse replace it with the proper size fuse and test the pump again. If there is power on both sides of the fuse check the water pump wiring connections at the wire nuts. It's possible for connections to come loose due to excessive vibration. Correct any loose connections and try the pump again. If the pump still doesn't work feel the motor to see if it is hot to the touch. If the motor is hot, a thermal breaker may have been triggered. Allow the pump time to cool off and see if it re-sets itself.
If you complete all of these tests and there is 12-volt DC power coming to the water pump motor, and it still doesn't come on, chances are the water pump is bad and it will need to be replaced.
Troubleshooting a 12-volt electrical problem in your RV is not that difficult. Follow the logical path of the device you are troubleshooting and see if you can determine where the problem is. It might be possible for you to save your well deserved vacation, some money and a trip to the RV dealership too.
Note: If you don't feel comfortable performing your own maintenance or troubleshooting the 12-volt electrical system, take your RV to a reputable repair center to have it checked out and repaired.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
These devices include overhead lights, the water pump, vent fans, furnace fan, range hood fan, LP gas leak detectors, stereos, 12-volt TVs and the refrigerator when it's operating in the LP gas mode. When camping you rely on these 12-volt items to operate properly, especially if you're dry camping without hook-ups. So what do you do when one of these 12-volt items quit working?
For the sake of an example let's say that we are dry camping and our 12-volt water pump quits working.
I am convinced that just about anybody is capable of troubleshooting a 12-VDC problem, and in many cases repairing the problem without it ruining a camping trip. For starters you'll need a couple of simple tools to assist you in troubleshooting your RV’s 12-volt electrical system.
1). An inexpensive 12-volt test light.
2). A multi-meter that can test for DC power.
Both of these are available at local auto parts stores. You should also keep some electrical tape, various size wire nuts, 12-volt light bulbs and 12-volt fuses on hand. Check the amperage of the fuses used in the power distribution box and keep an assortment. If you're aware of any inline fuses used on any of the 12-volt devices keep these on hand too.
Now, try to determine the last time the water pump actually worked. Did you leave the RV for a period of time with the pump on? Is there water in the fresh water holding tank? Were you working on or around something else that could have affected the operation of the water pump? Try to think of all possible scenarios. Something might jar your memory resulting in a quick fix to the problem.
If not, the first step is to verify that the coach battery or batteries are charged enough to supply power to these 12-volt items. There are a couple of ways to perform a quick test on the coach batteries. You can use the monitor panel to check their condition. For an accurate reading, make sure the RV is not plugged into electricity and turn on a couple of overhead lights to place a small load on the battery. Check the reading at the monitor panel. (If you check the reading at the monitor panel when the RV is plugged in to electricity it will give you fully charged reading) A more accurate method is to test the battery with a multi-meter. Set the meter to read 12-VDC and place the negative test probe on the negative battery terminal and the positive test probe on the positive battery terminal. A fully charged battery will read in the range of 12.6 to 12.7 volts. If it reads less than 12-volts it is below a 50 percent state of charge and will need to be charged.
IF THE BATTERY IS FULLY CHARGED, the next step is to make sure that any battery disconnect switch for the coach battery is turned on. If the battery disconnect switch is on, verify that other 12-volt devices in the RV are operating properly. If there is 12-volt power to the interior of the RV you need to check the fuse for the water pump in the power distribution center. Determine which fuse is for the water pump (fuses are normally labeled) and find a suitable ground for the 12-volt test light. Test both sides of the fuse for 12-volt power. If the test light only lights on one side of the fuse replace it with the proper size fuse and try the water pump again. If there was power at both sides of the fuse check for 12-volts at the water pump switch. If there is voltage, and the switch is operating properly check the water pump wiring for an inline fuse.
Find a good ground for the 12-volt test light and probe the wire on both sides of the fuse. If there is only power on one side of the fuse replace it with the proper size fuse and test the pump again. If there is power on both sides of the fuse check the water pump wiring connections at the wire nuts. It's possible for connections to come loose due to excessive vibration. Correct any loose connections and try the pump again. If the pump still doesn't work feel the motor to see if it is hot to the touch. If the motor is hot, a thermal breaker may have been triggered. Allow the pump time to cool off and see if it re-sets itself.
If you complete all of these tests and there is 12-volt DC power coming to the water pump motor, and it still doesn't come on, chances are the water pump is bad and it will need to be replaced.
Troubleshooting a 12-volt electrical problem in your RV is not that difficult. Follow the logical path of the device you are troubleshooting and see if you can determine where the problem is. It might be possible for you to save your well deserved vacation, some money and a trip to the RV dealership too.
Note: If you don't feel comfortable performing your own maintenance or troubleshooting the 12-volt electrical system, take your RV to a reputable repair center to have it checked out and repaired.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
Wednesday, October 29, 2008
Tips to make your RV fridge run more efficiently
If an RV refrigerator isn't running efficiently, in many cases it's something the owner did that affected its performance.
We can help the refrigerator do a better job. First and foremost, the RV must be fairly level for the refrigerator to operate properly. Older RV refrigerators required more precise leveling, but even newer models must be close to level for optimum performance. Over time, a cooling unit operated out of level will be permanently damaged. Traveling with the refrigerator operating will not cause problems because the liquids and gases in the cooling unit are constantly moving around. They don't collect and stay in areas of the cooling unit like they can in a stationary, out of level refrigerator.
The initial cool down process can take four to six hours. You should turn the refrigerator on the day before you plan to leave. When you put in the food, make sure it's already cold. Frozen food should already be frozen. Putting cold food in the refrigerator, rather than adding warm food, makes for less work for the refrigerator. One common mistake is to over pack a refrigerator. There must be space between the foods to allow for air to circulate throughout the compartment. On most RV trips, you will have access to a store to add to your food supply. So two to three day's worth should be enough.
To assist with air circulation you can purchase an inexpensive, battery operated refrigerator fan. Put the batteries in and place the fan in the front of the refrigerator compartment blowing up. Cold air drops and warm air rises. The fan will improve the efficiency by circulating the air and it will reduce the initial cool down time by half.
The heat created by the cooling process is vented behind the refrigerator. Air enters through the outside lower refrigerator vent and helps to draft the hot air out through the roof vent. Periodically inspect the back of the refrigerator and the roof vent for any obstructions like bird nests, leaves or other debris that might prevent the heat from escaping.
TO KEEP THE REFRIGERATOR OPERATING EFFICIENTLY in the LP gas mode, perform some routine maintenance. Remove the outside lower vent cover to access the back of the refrigerator. With the refrigerator turned off, ensure all connections are clean and tight. Turn the refrigerator on in the LP gas mode and look at the flame. If it's burning poorly, or is yellow-colored, or if the refrigerator isn’t operating properly in the gas mode it’s possible that the baffle inside the flue is covered with soot.
Soot, rust and other debris can fall down and obstruct the burner assembly. When this happens it's necessary to clean the flue and the burner assembly. Turn the refrigerator off again and locate the burner. Directly above the burner is the flue. The baffle is inside the flue. Wear a pair of safety glasses and use an air compressor to blow air up into the flue. After the flue is clean use the compressed air to remove any debris from the outside refrigerator compartment. Now, turn the refrigerator on in the LP gas mode to make sure it is working properly. Look for the bright blue flame. For a thorough cleaning of the flue and baffle it will be necessary to have your RV dealer do it for you. While it’s there have them to do an LP gas pressure test, too.
Another good idea is to install a 12 volt, thermostatically controlled refrigerator vent fan at the back of the refrigerator or at the top of the roof vent to assist with drafting the hot air away from the refrigerator. If you are mechanically inclined these fans are fairly easy to install, or you can have your RV dealer install one for you. Either way it’s worth it. The fan removes the heat built up behind the refrigerator improving the refrigerators performance by up to 40 percent.
Outside temperature affects the operation and efficiency of your RV refrigerator. When it’s cold outside you can lower the temperature setting and when it’s hot you can raise the setting. Some refrigerators are preset by the manufacturer. Extremely hot weather will directly affect the refrigerators efficiency. When it’s really hot outside try parking your RV with the refrigerator side in the shade. Periodically inspect and clean the refrigerator door gaskets. Check them for a good seal. Place a dollar bill behind the seal and close the door. It should stay there and not drop. When you try to pull it out there should be some resistance felt. Do this in several different places and have any damaged seals replaced.
Try to limit the amount of times you open the refrigerator or freezer doors and the length of time you leave the doors open. Every time the door is opened it loses a few degrees of heat. On a hot summer day it won’t take long to lose all of its cooling capacity. Last but not least you should always have a thermostat in the food compartment. Food will begin to spoil at temperatures above 40 degrees.
RV absorption refrigerators do a great job for RVers. They will do an even better job, and last longer, if we apply these simple tips to make their job easier and less demanding.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
Wednesday, October 15, 2008
Can a 30-amp electrical system run two air conditioners?
Dear Mark,
We are considering buying a Winnebago Sightseer 35J with two roof air conditioners. But the coach only has 30-amp service with an Onan 5.5 KW generator. Can these two air conditioners run at the same time with only 30 amps?
Mark Says: Most RV manufacturers use some type of energy management system so both roof air conditioners can operate at the same time on a 30-amp system. Our 2006 Bounder 35E is a good example. It will power up one A/C and then the other. Once they are both running it can sense if there's a requirement for more power placed on the system, like somebody making a pot of coffee, and it will shut one A/C down or both depending on the power requirement. When there is no longer a requirement the A/C units automatically start back up.
Many manufacturers use smaller BTU air conditioners. It was no good to have two 15,000 BTU units if you can only run one, so now they might use a 13,500 and an 11,000 BTU unit which a 30-amp system can run at the same time.
Basically what I am saying is most of today's manufacturers offer some type of power management system to operate both A/C units with a 30-amp system. On the other hand most manufacturers have a built-in system to prevent you from using both A/C units and attempt to use the microwave or other power consuming appliance.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
We are considering buying a Winnebago Sightseer 35J with two roof air conditioners. But the coach only has 30-amp service with an Onan 5.5 KW generator. Can these two air conditioners run at the same time with only 30 amps?
Mark Says: Most RV manufacturers use some type of energy management system so both roof air conditioners can operate at the same time on a 30-amp system. Our 2006 Bounder 35E is a good example. It will power up one A/C and then the other. Once they are both running it can sense if there's a requirement for more power placed on the system, like somebody making a pot of coffee, and it will shut one A/C down or both depending on the power requirement. When there is no longer a requirement the A/C units automatically start back up.
Many manufacturers use smaller BTU air conditioners. It was no good to have two 15,000 BTU units if you can only run one, so now they might use a 13,500 and an 11,000 BTU unit which a 30-amp system can run at the same time.
Basically what I am saying is most of today's manufacturers offer some type of power management system to operate both A/C units with a 30-amp system. On the other hand most manufacturers have a built-in system to prevent you from using both A/C units and attempt to use the microwave or other power consuming appliance.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
Monday, October 6, 2008
RVer's trailer keeps blowing out tires. What to do?
QUESTION: I have a 27 foot Dutchman travel trailer that I bought new in 2002. To date I have blown out seven tires. I am now on Goodyear radials having replaced the O.E. Carlyle tires. My question is this: Do tires on a trailer require balancing and alignment like a car? I just find it amazing that I have had that many blowouts.
Mark Says: My first thought would be that the tires are overloaded. If you haven't done it yet, take the trailer to a set of scales where you can weigh each wheel position separately. Compare the weights to the tire weight rating when they are inflated properly.
I have heard many people complain about Carlyle tires, but seven blowouts indicates some other type of problem. Balancing the tires cannot hurt but isn't absolutely necessary. Alignment for a trailer is usually related to one of the axles shifting over. If you stand in front of, and then behind the trailer look to see if both axles (tires) are aligned with each other. If one of the tires sticks out farther than the other take it in to have it checked out.
I still don't think this is what is causing the problem. Weigh the wheel positions and try distributing any weight in the trailer so none of the tires are overloaded. Another important factor is to make sure you are using replacement tires designed specifically for trailers. The sidewalls are designed to hold up to the twisting and flexing that occurs when you make turns etc.
Complete Guide to RVing
Thinking of becoming a full-time RVer? This is THE guide about how to do it. From dreaming about the lifestyle to living it, this fabulous resource has all the answers. This should be required reading for all aspiring full-timers or those who are new at it! Learn more or order!
Mark Says: My first thought would be that the tires are overloaded. If you haven't done it yet, take the trailer to a set of scales where you can weigh each wheel position separately. Compare the weights to the tire weight rating when they are inflated properly.
I have heard many people complain about Carlyle tires, but seven blowouts indicates some other type of problem. Balancing the tires cannot hurt but isn't absolutely necessary. Alignment for a trailer is usually related to one of the axles shifting over. If you stand in front of, and then behind the trailer look to see if both axles (tires) are aligned with each other. If one of the tires sticks out farther than the other take it in to have it checked out.
I still don't think this is what is causing the problem. Weigh the wheel positions and try distributing any weight in the trailer so none of the tires are overloaded. Another important factor is to make sure you are using replacement tires designed specifically for trailers. The sidewalls are designed to hold up to the twisting and flexing that occurs when you make turns etc.
Complete Guide to RVing
Thinking of becoming a full-time RVer? This is THE guide about how to do it. From dreaming about the lifestyle to living it, this fabulous resource has all the answers. This should be required reading for all aspiring full-timers or those who are new at it! Learn more or order!
Tuesday, September 30, 2008
Be careful about weight when choosing an RV tow vehicle
If you already have the vehicle that you plan to tow with, you need to find a trailer that is within the weight range of your vehicle. This was a common problem I ran into during my days as an RV sales manager. Customers would come in to purchase a travel trailer only to find out that their tow vehicle did not have a very good tow rating. It can be extremely frustrating to find the perfect travel trailer or fifth wheel and then be told that you can't tow it. On the other hand it can be worse if you go to a less reputable RV dealer and the sales person tells you that you can tow it! This happens every day, and this is why you need to be armed with the right information before you buy.
It is not my intention to upset any RV dealers, but if you go to a dealership and they don't ask you for information about the tow vehicle, it would be wise to go elsewhere. The first question my salespeople were required to ask was if you already had a tow vehicle. If so, they would look in our towing book and identify the tow capacity for your particular vehicle. Then we would inform you of your options. We lost many sales because the customer could not safely pull the camper they wanted, but we did not allow them to jeopardize themselves or their family.
If you don't already have the tow vehicle, it's a good idea to find the camper you want first and then buy a vehicle that is capable of safely towing it. I will caution you again, be careful if you listen to the salesperson at the auto dealership. They are only interested in selling you a vehicle, and a large percentage of salespeople do not understand vehicle tow ratings. Call a reputable RV dealer and ask them to check the vehicles tow rating before you buy it.
I once had a customer that found the camper they wanted and went to purchase a new truck. The salesperson told him the truck could tow 10,000 pounds. He went on to show my customer where 10,000 pounds was stamped into the hitch receiver on the back of the truck. The 10,000 pounds stamped in the receiver is what the receiver itself is rated for. It has absolutely nothing to do with the tow rating for the truck. My customer bought the truck and brought it to us to have the brake control and wiring done. I looked the truck up in my book and it was rated to tow 5,400 pounds. The camper weighed 6,000 pounds. I could write a book about stories like this, but our goal is to prevent this from happening to you.
There are many things to consider before you buy a tow vehicle. How often do you plan to tow? Where do you plan to tow? Is this vehicle going to be used strictly for towing, or will you be using it for everyday driving too? Are you interested in a pop-up, travel trailer or fifth wheel? How much does the camper you want weigh? Once you have answered these questions you can start looking for that perfect tow vehicle.
The manufacturer determines a vehicles tow rating. It is the maximum amount of weight that the vehicle can safely tow. The manufacturer takes many factors into consideration when determining a tow rating. They look at the vehicles engine size, transmission, axle ratio, chassis, suspension, brakes, tires, cooling capacity and many other things. Now this may all sound complicated, but the bottom line is determining how much can the vehicle safely tow. Do not assume that just because you're buying a truck it can tow a lot of weight. Most manufacturers offer vehicles with tow packages. A tow package upgrades the vehicles suspension, brakes, tires, and cooling system. They also add items like engine and transmission oil coolers to protect the vehicles major components when you are towing.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
It is not my intention to upset any RV dealers, but if you go to a dealership and they don't ask you for information about the tow vehicle, it would be wise to go elsewhere. The first question my salespeople were required to ask was if you already had a tow vehicle. If so, they would look in our towing book and identify the tow capacity for your particular vehicle. Then we would inform you of your options. We lost many sales because the customer could not safely pull the camper they wanted, but we did not allow them to jeopardize themselves or their family.
If you don't already have the tow vehicle, it's a good idea to find the camper you want first and then buy a vehicle that is capable of safely towing it. I will caution you again, be careful if you listen to the salesperson at the auto dealership. They are only interested in selling you a vehicle, and a large percentage of salespeople do not understand vehicle tow ratings. Call a reputable RV dealer and ask them to check the vehicles tow rating before you buy it.
I once had a customer that found the camper they wanted and went to purchase a new truck. The salesperson told him the truck could tow 10,000 pounds. He went on to show my customer where 10,000 pounds was stamped into the hitch receiver on the back of the truck. The 10,000 pounds stamped in the receiver is what the receiver itself is rated for. It has absolutely nothing to do with the tow rating for the truck. My customer bought the truck and brought it to us to have the brake control and wiring done. I looked the truck up in my book and it was rated to tow 5,400 pounds. The camper weighed 6,000 pounds. I could write a book about stories like this, but our goal is to prevent this from happening to you.
There are many things to consider before you buy a tow vehicle. How often do you plan to tow? Where do you plan to tow? Is this vehicle going to be used strictly for towing, or will you be using it for everyday driving too? Are you interested in a pop-up, travel trailer or fifth wheel? How much does the camper you want weigh? Once you have answered these questions you can start looking for that perfect tow vehicle.
The manufacturer determines a vehicles tow rating. It is the maximum amount of weight that the vehicle can safely tow. The manufacturer takes many factors into consideration when determining a tow rating. They look at the vehicles engine size, transmission, axle ratio, chassis, suspension, brakes, tires, cooling capacity and many other things. Now this may all sound complicated, but the bottom line is determining how much can the vehicle safely tow. Do not assume that just because you're buying a truck it can tow a lot of weight. Most manufacturers offer vehicles with tow packages. A tow package upgrades the vehicles suspension, brakes, tires, and cooling system. They also add items like engine and transmission oil coolers to protect the vehicles major components when you are towing.
Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.
Subscribe to:
Posts (Atom)