Your house-on-wheels sat in storage for several months this winter and now it’s time for another camping season. What do you check to make sure the RV is safe and ready to use when you head out on your first RV trip of the season? There are lots of preventive maintenance checks you can perform, but here are the checks I consider essential.
1) Batteries: Start your post-winter checks with the batteries since it’s possible you removed them for winter storage. The condition of the batteries is dependent on how well they were cared for over the winter. Batteries in storage will lose a percentage of current through internal leakage. It’s not uncommon for a battery to discharge up to 10% a month when it is in storage. If you checked and recharged the batteries periodically while in storage they should be ready to go. If not, the first step is to fully charge the battery(s). Water should only be added to lead acid batteries after fully charging the battery, unless the water level is already below the plates. The plates need to be covered at all times. After the battery if fully charged check and add distilled water as required. If the batteries were removed for storage reinstall them making absolutely sure they are connected properly.
2) RV Water System (de-winterize/check for leaks/sanitize): Depending on how the unit was winterized it needs to be de-winterized. If you used non-toxic RV antifreeze to protect the water system you need to run fresh water through the entire system until all traces of the antifreeze are removed. Hopefully no antifreeze was added to the fresh water holding tank. If it was, the first step is to drain any remnants from the tank. Add potable water to the fresh water holding tank, turn the water pump on and open all of the water faucets. When clear water is running through the system turn the pump off and close the faucets. Take the water heater out of the by-pass mode (if applicable). If the water heater wasn’t bypassed the antifreeze needs to be drained from the water heater tank. Replace any water filter cartridges you removed for storage.
This is a good time t check the plumbing for leaks. With water in the fresh water holding tank turn the 12-volt water pump on and pressurize the water system until the pump shuts off. If the water pump cycles back on, even for a short period of time, there may be a leak somewhere. Try to locate the leak and repair it or take it to an authorized RV service facility to be repaired.
At this point I like to sanitize the water system (see video at the end of this post). Make sure all of the drains are closed and drain plugs are installed. Take a quarter-cup of household bleach for every fifteen gallons of water your fresh water tank holds. Mix the bleach with water into a one-gallon container and pour it in to the fresh water holding tank. Fill the fresh water holding tank completely full of water. Turn the water pump on and run water through all hot and cold faucets until you smell the bleach. Close the faucets and let it sit for twelve hours. Drain all of the water and re-fill the tank with potable water. Turn the water pump on and open all faucets, running the water until you no longer smell any bleach. It may be necessary to repeat this process to eliminate all signs of bleach.
3) Appliance Checks: Open the LP gas valve and check the operation of all LP gas fired appliances. Make sure the water heater tank is full of water before testing the water heater. If an LP gas appliance is not operating properly have it inspected by an authorized RV service facility. Insects are attracted to the odorant added to LP gas and nests can affect the appliance from operating properly.
Note: The LP gas system should have a leak test and gas operating pressure test preformed annually. These tests should be performed by an authorized RV repair facility.
Plug the unit into a reliable source of electricity and test 120-volt appliances and accessories for proper operation. Note: Make sure you have an adequate electrical source (30-50 amps) depending on your unit, before testing items like the microwave and roof air conditioner(s). After checking the refrigerator in the LP gas mode turn it off and with the doors open allow sufficient time for it to return to room temperature before checking it in the electric mode.
4) Tire Check: Just like a battery looses a percentage of its charge in storage, tires lose a percentage of air pressure. Your tires can lose 2-3 psi a month while sitting in storage. Check the tire pressure with a quality tire inflation gauge and adjust the inflation pressure to the manufacturer’s recommendation based on the load. Remember failing to maintain correct tire pressure, based on the load, can result in fast tread wear, uneven wear, poor handling, and excessive heat build-up which can lead to tire failure. Tire manufacturers publish load and inflation tables that should be followed for proper inflation pressure.
5) RV or Tow Vehicle Engine: Check all fluid levels. Check the transmission, power steering, engine coolant, engine oil, windshield washer and brake fluid. Consult your vehicle owner’s manual for proper levels. If a fluid level is low try to determine why and correct the problem. Service the engine and engine fluid levels according to specified intervals found in the owner’s manual. Start the engine and check for proper readings on all gauges. Check the operation of all lights. Make sure the vehicle emissions / inspection sticker is up to date.
If you have a generator check the oil level in the generator. Service the generator according to specified intervals found in the owner’s manual. Inspect the generator exhaust system for any damage prior to starting. Never run a generator with a damaged exhaust system. If you didn’t run the generator during storage start and run it for about two hours with at least a half-rated load. Check your generator owner’s manual for load ratings. If you didn’t use a fuel stabilizer and the generator won’t start, or continues to surge after starting, have it checked out and repaired by an authorized service facility.
6) Sealants & Seams: If you didn’t inspect the seams and sealants for potential leaks prior to storage or if the RV was stored outdoors this is a good time to do it. I recommend inspecting and resealing seams and sealants at least twice a year and possibly more depending on conditions. Inspect all roof and body seams and around any openings cut into the RV for signs of cracking or damage. Reseal any seams or sealants that show signs of cracking or separation. It’s important you consult your RV owner’s manual, or RV dealer, for sealants compatible with different types of materials you are attempting to seal. If you don’t feel comfortable performing the inspections or repairing seams and sealants have the maintenance performed by an authorized service facility. Note: Be extremely careful working on the RV roof. A fall can cause serious injury or death.
7) RV Safety Checks: Re-install any dry-cell batteries or fuses that were removed for storage. If batteries were not removed from safety devices replace them with new batteries now. Test the operation of the carbon monoxide detector, LP gas leak detector and smoke alarm. Inspect all fire extinguishers to make sure they are fully charged. If you have dry powder fire extinguishers shake and tap on the bottom to release the powder from the bottom.
These are what I consider to be essential post-winter checks so your RV is ready to roll when you are. You can add to this list and tailor it to your specific needs. Be safe and have a great camping season.
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Thursday, April 26, 2012
Monday, April 16, 2012
RVing at Wal-mart - One Bad Apple Spoils the Barrel
I am sure you have heard the expression “one bad apple spoils the barrel” at one time or another. When we travel in our RV and just want a few hours rest we usually stop and stay at a Wal-Mart along the way. Whenever we do this there is an unwritten protocol we follow to ensure that staying in a Wal-Mart parking lot remains an option for RVers in the future.
1) Always ask for permission to stay.
2) Always ask where they would like you to park. Never block loading zones.
3) Do not put out the lawn chairs, awning & BBQ grill.
4) Do not stay for more than one evening.
5) Do not use leveing jacks in the parking lot. The weight of the RV can cause damage to the asphalt. (See photo above)
There are more common-sense rules that apply, but these are what I consider to be some of the more important points to follow. We also reciporcate by shopping at the Wal-Mart to re-supply and re-stock the RV with any essential items.
Many Wal-Mart stores around the country offer this overnight parking service to RV owners until somebody spoils it for everybody. It’s easy to quietly pull-in, park, spend the evening, clean up after yourself and leave in the morning.
Try not to be the bad apple when it comes to staying at a Wal-Mart in your RV!
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
1) Always ask for permission to stay.
2) Always ask where they would like you to park. Never block loading zones.
3) Do not put out the lawn chairs, awning & BBQ grill.
4) Do not stay for more than one evening.
5) Do not use leveing jacks in the parking lot. The weight of the RV can cause damage to the asphalt. (See photo above)
There are more common-sense rules that apply, but these are what I consider to be some of the more important points to follow. We also reciporcate by shopping at the Wal-Mart to re-supply and re-stock the RV with any essential items.
Many Wal-Mart stores around the country offer this overnight parking service to RV owners until somebody spoils it for everybody. It’s easy to quietly pull-in, park, spend the evening, clean up after yourself and leave in the morning.
Try not to be the bad apple when it comes to staying at a Wal-Mart in your RV!
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Sunday, April 8, 2012
Make Your RV Water Taste Like . . . Water
Take care of your RV water system and in return, it will provide you with years of dependable service.
The potable water system in your house is pretty much maintenance-free. The potable water system in your RV, on the other hand, requires some maintenance to keep it trouble-free. Something I've run into quite often is the complaint that there is a stale odor coming from the RV water system.
When you return from a trip and you are not going to use the RV for a while, you need to drain the entire water system to prevent it from getting stale and musty. You can start by draining the water heater.
Go to the outside compartment where the water heater is located. The drain plug, or petcock, is located in the bottom left hand corner. Remove the plug and open the pressure relief valve on top of the water heater to assist in draining. Caution: Never drain the water heater when it is hot or under pressure. Next you need to locate the low point water line drains. It may take a while to find them, but I assure you they are there. There will be one for the hot and one for the cold water lines. This is the lowest point in the water system. Open these and let the water drain out.
The potable water system in your house is pretty much maintenance-free. The potable water system in your RV, on the other hand, requires some maintenance to keep it trouble-free. Something I've run into quite often is the complaint that there is a stale odor coming from the RV water system.
When you return from a trip and you are not going to use the RV for a while, you need to drain the entire water system to prevent it from getting stale and musty. You can start by draining the water heater.
Go to the outside compartment where the water heater is located. The drain plug, or petcock, is located in the bottom left hand corner. Remove the plug and open the pressure relief valve on top of the water heater to assist in draining. Caution: Never drain the water heater when it is hot or under pressure. Next you need to locate the low point water line drains. It may take a while to find them, but I assure you they are there. There will be one for the hot and one for the cold water lines. This is the lowest point in the water system. Open these and let the water drain out.
There is one more thing left to do, find the drain for the fresh water holding tank and drain all of the water from it. At this point you can turn the water pump on for a moment to force any remaining water out. Do not let the pump continue to run once the water stops draining. Close all the drains.
If by accident you forget to drain the water system and you get that notorious stale odor all is not lost, you just need to sanitize the water system. Start by draining all of the old water out, and close all of the drains. Take a quarter-cup of house-hold bleach for every fifteen gallons of water that your fresh water tank holds. Mix the bleach into a one-gallon container and pour it into the fresh water holding tank. Fill the fresh water tank completely full of water. Turn the water pump on, open all hot and cold faucets and run the water until you smell the bleach at each faucet. Close the faucets and let it sit for 12 hours. Drain the entire system and re-fill the fresh water tank with water. Open all of the faucets and run the water until you no longer smell any bleach. It may be necessary to repeat this process again to eliminate all signs of bleach from the water system. Once this is done it is safe to use your water system. It's also a good idea to use a water filter at campgrounds and to keep bottled water on hand for drinking.
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Thursday, April 5, 2012
Do you Know Your RV Batteries?
Motorized RVs have different requirements for different types of batteries. They need a starting battery, similar to your automobile to start the engine and supply power to the 12-volt DC automotive system and a deep cycle battery(s) for the coach's 12-volt DC electrical system. The house or coach batteries, as they are commonly called, need to be true deep cycle batteries that are designed to provide a steady amount of current over a long period of time. Starting batteries and marine batteries should not be used in this application. True deep cycle batteries have much thicker plates and are designed to be deeply discharged and recharged over and over again.
Many towable and motorized RVs use a single deep cycle battery. Deep cycle batteries are rated in amp hours. How many amps the battery can deliver for how many hours before the battery is discharged. If you enjoy dry-camping, without utility hook-ups, you depend on your deep cycle battery(s) to take care of your 12-volt needs. You can purchase a deep cycle battery with a higher amp hour capacity that will last longer. The higher the amp hour capacity is the larger and heavier the battery is. If you have room for a larger battery and enjoy dry-camping you may want to upgrade your deep cycle battery to one with a higher amp hour rating. If your RV came equipped with a RV/Marine battery I suggest you upgrade to a true deep cycle battery.
Watch my video below for helpful RV battery tips to extend the life of your deep cycle RV batteries:
Watch my video below for helpful RV battery tips to extend the life of your deep cycle RV batteries:
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Many towable and motorized RVs use a single deep cycle battery. Deep cycle batteries are rated in amp hours. How many amps the battery can deliver for how many hours before the battery is discharged. If you enjoy dry-camping, without utility hook-ups, you depend on your deep cycle battery(s) to take care of your 12-volt needs. You can purchase a deep cycle battery with a higher amp hour capacity that will last longer. The higher the amp hour capacity is the larger and heavier the battery is. If you have room for a larger battery and enjoy dry-camping you may want to upgrade your deep cycle battery to one with a higher amp hour rating. If your RV came equipped with a RV/Marine battery I suggest you upgrade to a true deep cycle battery.
Watch my video below for helpful RV battery tips to extend the life of your deep cycle RV batteries:
Watch my video below for helpful RV battery tips to extend the life of your deep cycle RV batteries:
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Subscribe to:
Posts (Atom)
