Wednesday, October 15, 2008

Can a 30-amp electrical system run two air conditioners?

Dear Mark,
We are considering buying a Winnebago Sightseer 35J with two roof air conditioners. But the coach only has 30-amp service with an Onan 5.5 KW generator. Can these two air conditioners run at the same time with only 30 amps?

Mark Says: Most RV manufacturers use some type of energy management system so both roof air conditioners can operate at the same time on a 30-amp system. Our 2006 Bounder 35E is a good example. It will power up one A/C and then the other. Once they are both running it can sense if there's a requirement for more power placed on the system, like somebody making a pot of coffee, and it will shut one A/C down or both depending on the power requirement. When there is no longer a requirement the A/C units automatically start back up.

Many manufacturers use smaller BTU air conditioners. It was no good to have two 15,000 BTU units if you can only run one, so now they might use a 13,500 and an 11,000 BTU unit which a 30-amp system can run at the same time.

Basically what I am saying is most of today's manufacturers offer some type of power management system to operate both A/C units with a 30-amp system. On the other hand most manufacturers have a built-in system to prevent you from using both A/C units and attempt to use the microwave or other power consuming appliance.

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Monday, October 6, 2008

RVer's trailer keeps blowing out tires. What to do?

QUESTION: I have a 27 foot Dutchman travel trailer that I bought new in 2002. To date I have blown out seven tires. I am now on Goodyear radials having replaced the O.E. Carlyle tires. My question is this: Do tires on a trailer require balancing and alignment like a car? I just find it amazing that I have had that many blowouts.

Mark Says: My first thought would be that the tires are overloaded. If you haven't done it yet, take the trailer to a set of scales where you can weigh each wheel position separately. Compare the weights to the tire weight rating when they are inflated properly.

I have heard many people complain about Carlyle tires, but seven blowouts indicates some other type of problem. Balancing the tires cannot hurt but isn't absolutely necessary. Alignment for a trailer is usually related to one of the axles shifting over. If you stand in front of, and then behind the trailer look to see if both axles (tires) are aligned with each other. If one of the tires sticks out farther than the other take it in to have it checked out.

I still don't think this is what is causing the problem. Weigh the wheel positions and try distributing any weight in the trailer so none of the tires are overloaded. Another important factor is to make sure you are using replacement tires designed specifically for trailers. The sidewalls are designed to hold up to the twisting and flexing that occurs when you make turns etc.


Complete Guide to RVing
Thinking of becoming a full-time RVer? This is THE guide about how to do it. From dreaming about the lifestyle to living it, this fabulous resource has all the answers. This should be required reading for all aspiring full-timers or those who are new at it! Learn more or order!

Tuesday, September 30, 2008

Be careful about weight when choosing an RV tow vehicle

If you already have the vehicle that you plan to tow with, you need to find a trailer that is within the weight range of your vehicle. This was a common problem I ran into during my days as an RV sales manager. Customers would come in to purchase a travel trailer only to find out that their tow vehicle did not have a very good tow rating. It can be extremely frustrating to find the perfect travel trailer or fifth wheel and then be told that you can't tow it. On the other hand it can be worse if you go to a less reputable RV dealer and the sales person tells you that you can tow it! This happens every day, and this is why you need to be armed with the right information before you buy.

It is not my intention to upset any RV dealers, but if you go to a dealership and they don't ask you for information about the tow vehicle, it would be wise to go elsewhere. The first question my salespeople were required to ask was if you already had a tow vehicle. If so, they would look in our towing book and identify the tow capacity for your particular vehicle. Then we would inform you of your options. We lost many sales because the customer could not safely pull the camper they wanted, but we did not allow them to jeopardize themselves or their family.

If you don't already have the tow vehicle, it's a good idea to find the camper you want first and then buy a vehicle that is capable of safely towing it. I will caution you again, be careful if you listen to the salesperson at the auto dealership. They are only interested in selling you a vehicle, and a large percentage of salespeople do not understand vehicle tow ratings. Call a reputable RV dealer and ask them to check the vehicles tow rating before you buy it.

I once had a customer that found the camper they wanted and went to purchase a new truck. The salesperson told him the truck could tow 10,000 pounds. He went on to show my customer where 10,000 pounds was stamped into the hitch receiver on the back of the truck. The 10,000 pounds stamped in the receiver is what the receiver itself is rated for. It has absolutely nothing to do with the tow rating for the truck. My customer bought the truck and brought it to us to have the brake control and wiring done. I looked the truck up in my book and it was rated to tow 5,400 pounds. The camper weighed 6,000 pounds. I could write a book about stories like this, but our goal is to prevent this from happening to you.

There are many things to consider before you buy a tow vehicle. How often do you plan to tow? Where do you plan to tow? Is this vehicle going to be used strictly for towing, or will you be using it for everyday driving too? Are you interested in a pop-up, travel trailer or fifth wheel? How much does the camper you want weigh? Once you have answered these questions you can start looking for that perfect tow vehicle.

The manufacturer determines a vehicles tow rating. It is the maximum amount of weight that the vehicle can safely tow. The manufacturer takes many factors into consideration when determining a tow rating. They look at the vehicles engine size, transmission, axle ratio, chassis, suspension, brakes, tires, cooling capacity and many other things. Now this may all sound complicated, but the bottom line is determining how much can the vehicle safely tow. Do not assume that just because you're buying a truck it can tow a lot of weight. Most manufacturers offer vehicles with tow packages. A tow package upgrades the vehicles suspension, brakes, tires, and cooling system. They also add items like engine and transmission oil coolers to protect the vehicles major components when you are towing.

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Friday, November 23, 2007

How to store an RV for the winter season

Snow has arrived in many parts of the country and before long it will be Christmas. What does this mean to many RVers? Well, besides shoveling sidewalks and last minute Christmas shopping it means parking the RV until next spring.

Most of us have already winterized our RVers, but did you really prepare your RV for several months of storage? Many of us don't think about it, but the storing portion is just as important as winterizing the water system. Actually winterizing your RV encompasses much more than protecting the water system from freezing temperatures. It's just that we're under the impression that winterizing means to put that pink non-toxic antifreeze through our water system and everything will be okay.

When I produced our winterizing video I included an entire section on properly storing the RV. It's important that we consider things like batteries, ventilation, the condition of sealants, mice, and fuel system protection just to mention a few.

Let's look at some things we should do in addition to winterizing our RV water system. The storage procedures are divided into two sections, the coach storage and the chassis storage. Follow the steps below that apply to your RV:

Coach Storage


Store your unit under a covered area if possible. If not, avoid parking under trees or in areas where grass and weeds will grow.

If you choose to buy a cover for the RV, be sure it is made of a breathable material. This will help in preventing mold and mildew.

Chock the wheels front and rear. Leave the parking brake off. If you're storing a Pop Up trailer, angle the tongue downward to assist in snow and water run off.

Inflate the tires to the manufacturer's recommended maximum cold pressure. Cover the tires to protect them from harmful ultraviolet rays. Place something between the tires and the ground, making sure whatever you use is larger than the actual footprint of the tire.

If you do not remove the tires for long-term storage periodically move the vehicle to prevent flat spots.

Close all of the window blinds to avoid sun exposure to the carpet, drapes and upholstery.

Wash the exterior of the unit and clean the interior thoroughly.

Make sure the awning fabric is clean and dry before storing.

On a Pop Up trailer make absolutely sure the fabric is clean and dry before storing. This is a good time to check for tears, and repair the fabric.

Inspect all roof seams, body seams and window sealant for cracks and openings. Water can get in the smallest openings so really inspect all sealants. Consult your dealer for sealants compatible with these materials.

Service all locks with a graphite spray lubricant. Lubricate all hinges and moving parts with WD 40.

Turn all LP gas appliances off. Turn the main LP gas supply valve off. If you're storing a Pop Up or travel trailer make sure the LP gas regulator is covered.

Remove the fuse for the LP gas leak detector while the unit is in storage. This will prevent the batteries from discharging. Don't forget to replace it next spring.

Insects are attracted to the odorant that is added to LP gas. To prevent mud daubers and wasps from building nests in and around your gas appliances, cover the refrigerator vent, the furnace vent and the water heater vent.

Inspect the underside of the unit thoroughly. Look for anywhere that mice or other rodents can get it, and seal as necessary.

Strategically place mouse and ant traps in and around the unit. Avoid using mouse poison inside the RV. Many RVers recommend using dryer sheets like Bounce to keep mice out.

Remove all perishables and anything that can freeze.

Leave doors, drawers and cabinets open.

Remove all consumables that would attract mice and other rodents.

Defrost the freezer compartment and clean the refrigerator. Leave the refrigerator doors open and place some baking soda inside to absorb odors.

Clean the air conditioner filters, and cover the air conditioner.

Turn off the main breaker and unplug all appliances.

Remove dry cell batteries in clocks, flashlights and other items.

The use of Maxx Air products will provide the airflow and ventilation required during storage while keeping the elements out.

Chassis Storage

To start with if you put your RV in storage it's a good idea to remove the batteries and put them in storage too. When you're removing the batteries always remember to remove the negative terminal first. Clean the batteries with a 50/50 mixture of baking soda and water if necessary. Store the batteries in a cool dry place but not where they could freeze. Batteries in storage will loose their charge. Check the state of charge every month and charge batteries that are at or below 80 percent state of charge.

Check and fill the water levels in all batteries that are not maintenance free. Check the electrolyte level and add distilled water if necessary.

Charge all batteries as required. A discharged or partially charged battery will freeze much faster than a charged battery.

Remove and clean all battery terminals and posts. Spray the terminals with terminal dressing to protect against corrosion.

If you plan to start the unit while in storage, and to periodically plug the unit into shore power leave the batteries in the unit. Plugging it into shore power once a month for about eight hours will keep the coach batteries topped off.

If you put the unit in long-term storage; remove and store the batteries where they will not freeze. In either case keep the batteries charged.

During short-term storage, start the unit monthly and run it with the dash air on for at least 30 minutes.

If you don't plan on starting the unit, or won't be able to start it, buy some fogging oil from a marine supply store to protect the cylinder walls. When the unit is parked where it will be stored, spray the fogging oil into the engine intake downstream from the air filter with the engine at an idle. Complete the same steps on the generator. Follow the manufacturer's directions. DO NOT USE THIS PRODUCT IN A DIESEL ENGINE

Fill the fuel tank prior to storage and add a fuel stabilizer. Run the engine and the generator long enough for the stabilizer to get through the system. Follow the manufacturer's directions.

If the unit is not in long-term storage, exercise the generator at least two hours each month. Run the generator at 3/4 rated load. Consult your generator set owners manual for rated loads.

Change the oil and oil filter on the engine and the generator prior to storage. Acids accumulate in used oil and can corrode engine bearings.

Check the engine radiator for the proper concentration of antifreeze. Consult your owner's manual for the correct type of engine antifreeze. Drain, flush and refill the system every two to three years.

Drain the windshield washer reservoir or add the appropriate antifreeze solution to prevent it from freezing.

Perform full chassis lubrication prior to storage.

Now your RV is truly winterized and hopefully you won't experience any problems when you perform your spring maintenance checks next year.

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Sunday, September 30, 2007

How to operate your RV awning properly

RV awnings vary from manufacturer to manufacturer, and there are many awning manufacturers. This is the awning operation checklist from my Checklists for RVers E-book. The purpose of this checklist is to give you a basic guide to follow when opening and storing the retractable patio awning for your motorhome, travel trailer, fifth wheel trailer or other RV. It may not cover every item as it pertains to your awning; so only use the checks that apply to your RV's particular awning.

Most awnings have some type of travel locks about midway up, on both main awning arms. These locks assist in storing the awning to the side of the RV while traveling. Release these locking mechanisms.

Behind both main awning arms, on the support arms, there will be a knob that should be hand tight. Loosen both of these knobs. Look up at the end of the awning roller tube on the right hand side, towards the front of the RV. You will see a small lever. This lever is what locks the roller tube to the side of the RV. Take your awning rod and with the hooked end reach up and pull the lever down to release the roller tube.

Look up, around the middle of the roller tube, and you should see the end of the awning strap, with a loop in it. With the hook end of your awning rod reach up and hook the awning strap loop. Using the awning rod, pull the awning strap down until you can reach it with your hand. The awning roller tube should release and pull freely from both ends. Continue pulling down on the strap until the awning fabric and tube are fully extended. Now, the inner support arms, where you loosened the knobs, should slide freely to the top of the main arms and lock into place. Do this on both ends. When they are locked in place, starting on either end, take one hand and pull down on the main awning arm until the awning fabric is taught. With your other hand reach up and hand tighten the knob. Repeat this on the other end.

On the side of each main arm you will notice a lever. Starting on either end of the awning, take one hand and put it on the front of the main arm and take the lever with your other hand. Raise the main arm up to the height you want the awning, using the lever to help lift it. When you lower the lever it will lock into the closest adjusting hole on the arm where you release it. Repeat this on the other end.

Caution: Do not get your fingers or hands close to any moving or sliding parts.

Retracting your Patio Awning

Put one hand on the front of the main awning arm and the other hand on the lever on the side of the arm. As soon as you pull out on the lever the awning arm will begin to lower. Caution: keep fingers and hands away from moving and sliding awning parts. Using the lever for support slowly lower the main arm until it stops. Repeat on the other end.

Reach up and loosen the knob on one of the support arms. On the front of the main arm, towards the top, pull the release latch out that is locking the support arm in place. Holding the latch out begin to slide the support arm down the main arm. Continue to slide it all the way down until it stops. Repeat on the other end. Again watch your fingers.

If you are retracting the awning by yourself take your awning rod in one hand and with your other hand take the awning strap and slide it all the way down the awning tube, to where the awning lock lever is located, towards the front of the RV.

Pull down on the awning strap, applying enough pressure, until you can release the awning lock lever. Caution: as soon as the lever is released the awning tube will begin to retract. These tubes have springs that are wound with tension. Hold the strap securely and release the locking lever. Continue to hold the strap firmly and work it back to the middle of the awning tube by sliding it in the groove.

When the awning strap is close to the middle of the roller tube slowly let the awning begin to retract by easing off the awning strap. Place the hook end of the awning rod into the loop of the strap and continue to retract the awning until it is in the stored position. Do not let go of the strap too early. The awning can violently hit the side of the RV causing damage to the awning and/or the RV.

Secure the travel locks on both main arms and hand tighten both knobs on the back of the support arms.

Awning Tip: If somebody is assisting you the 3rd and 4th steps are much easier. Locate the awning strap in the middle of the awning tube. Have the person assisting you hold tension on the strap while you release the awning lock lever. Then, using the awning rod the person assisting you can slowly allow the awning to retract.

Well that about does it. With the proper care and a little preventive maintenance you and your RV awnings will have it made in the shade.

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Sunday, September 23, 2007

Follow these steps to winterize your RV

Fall is the time of year when many RVers lock up their RV for the cold-weather season ahead. Parking your RV for the winter requires some preventive measures so it will be ready to use next spring. You'll also be glad you did it when you don't have costly repair bills due to the damaging results of winter. Now the question is how do you prepare your recreational vehicle for winter, and who will be doing it? If you're like me and you enjoy performing the routine maintenance on your RV, not to mention saving a few dollars, the "who" part is answered. As for the "how" part, this checklist is the same one I used to make my Winterizing & Storing DVD. I feel it is the easiest and most effective way to winterize your RV.

Before you get started there are a few items you will need. They can be found in most RV parts stores:

*Non-toxic RV antifreeze (the amount depends on the layout and length of your plumbing lines. Two to three gallons will normally do).

*A water heater by-pass kit, if not already installed.

*A water pump converter kit, or tubing to connect to the inlet side of the water pump.

*Basic hand tools to remove drain plugs.

Now we can winterize the RV water system to protect it from freezing. Be sure to read your owners manuals for unit specific winterizing guidelines. Follow the steps below that apply to your RV.

*If you have any inline water filters remove and bypass them before starting.

*Drain the fresh water holding tank.

*Drain and flush the gray and black holding tanks. Clean the black tank with a wand. Lubricate the termination valves.

*Drain the water heater. CAUTION: Never drain when hot or under pressure.

*Open all hot and cold faucets; don't forget the toilet valve and outside shower.

*Locate and open low point drain lines. Using the water pump will help force water out, but turn it off as soon as the system is drained.

*Recap all drains and close all faucets.

*By-pass the water heater. If you do not have a by-pass kit installed the water heater will fill up with antifreeze before it goes through the water lines, wasting six gallons of antifreeze.

*Install a water pump converter kit, or disconnect the inlet side of the pump (the line coming from the fresh water holding tank) and connect tubing from the pump into a gallon of RV antifreeze.

*Turn the water pump on and pressurize the system. Starting with the closest faucet slowly open the hot and then cold valves until antifreeze appears. Replace antifreeze jug as required.

*Repeat on all faucets from the closest to farthest away. Don't forget the outside shower.

*Flush the toilet until antifreeze appears.

*Turn the water pump off and open a faucet to release the pressure. Go to the city water inlet.

*Remove the small screen over the inlet and push in on the valve with a small screwdriver until you see antifreeze. Replace the screen.

*Pour a cupful of antifreeze down each drain. Pour a few cups in the toilet and flush into the holding tank.

*If your water heater has an electric heating element turn it off. This will protect the element if the unit is plugged in while being stored.

*Make sure all faucets are closed.

*Consult your owner manuals for winterizing ice makers and washing machines.

Your RV is winterized!

This checklist is a basic guide that was intended to assist you in winterizing your RV. As with many other checklists it would be impossible to cover every RV. It is extremely important that you read your owners manuals for unit specific winterizing guidelines. --Mark Polk

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Tuesday, September 4, 2007

How to extend the life of an RV battery

How long your RV batteries last depends on how you use them. Factors include how they're used, how well they're maintained, how they're discharged, how they're re-charged, and how they are stored. A battery cycle is one complete discharge from 100 percent down to about 50 percent and then re-charged back to 100 percent.

One important factor to battery life is how deep the battery is cycled each time. If the battery is discharged to 50 percent everyday it will last twice as long as it would if its cycled to 80 percent. Keep this in mind when you consider a batteries amp hour rating. The amp hour rating is really cut in half because you don't want to completely discharge the battery before recharging it. The life expectancy depends on how soon a discharged battery is recharged. The sooner it is recharged the better.

What does all of this mean to you? That depends on how you use your RV. If most of your camping is done where you're plugged into an electrical source then your main concern is simply to properly maintain your deep cycle batteries. But if you like to do some serious dry-camping you'll want the highest amp hour capacities you can fit on your RV.

Deep cycle batteries come in different sizes. Some are designated by group size, like Group 24, 27 and 31. Basically the larger the battery the more amp hours you get. Depending on your needs and the amount of space you have available, there are several options when it comes to batteries. You can use one 12-volt Group 24 deep cycle battery that provides 70 to 85 amp hours or you can use two or more 12-volt batteries wired in parallel. Parallel wiring increases amp hours but not voltage.

If you have the room you can do what a lot of RVers do and switch from the standard 12-volt batteries to two of the larger 6-volt golf cart batteries. These pairs of 6-volt batteries need to be wired in series to produce the required 12-volts. Series wiring increases voltage but not amp hours. If this still doesn't satisfy your requirements you can build larger battery banks using four 6-volt batteries wired in series/parallel that will give you 12-volts and double your AH capacity. --Mark Polk

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.