Thursday, January 8, 2009

Why to put wood under RV tires during storage

It's a good idea to get the weight off of tires when an RV will be in storage for a period of time. But, this is not always practical or even possible. If the weight can't be removed, at a minimum you should try to move the RV every three months to prevent tire flat spots and ozone cracking at the tire sidewall flex point. Flat spots will usually disappear after the tires warm up and travel for a distance, unless the vehicle hasn't been moved for six months or more.

There are actually several reasons for blocking tires. The first step is to make sure the RV is as level as possible so more weight isn't on one tire than the others. The perfect scenario would be to store the RV and its tires in a cool dry, covered area, but as we all know this is not always possible either.

STORAGE SURFACE AREAS can cause your tires to age prematurely. You don't want to leave the tires in contact to any heat producing material or petroleum based material like asphalt. You also don't want them exposed to constant cold or moisture, like sitting on the frozen ground. The wood acts as a barrier between the tires and the ground surface they are being stored on. The proper storage steps would be to clean the tires, cover them to protect them from harmful sunlight and UV rays and inflate them to the pressure indicated on the sidewall of the tires.

It is extremely important that the blocking you use is wider than the tires tread and longer than the tires overall footprint. If not the steel cables in the tires sidewall can be damaged which can also result in premature tire failure.

Also, you can use Lynx Levelers, just make sure you follow the directions above.

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Wednesday, December 31, 2008

Carrying portable air compressor in your RV is good idea

Every RVer needs to understand the importance of tires and proper tire pressure. The problem that can sometimes occur is while on the road, there is no available air support to check tire pressure. If you wait until you're on the road to check tire pressure, the tires are too hot for correct evaluation.

This is a common problem for RVers, and that is why you might want to consider a portable air compressor. Here are a few pointers when deciding what compressor to purchase: The rate that a compressor can deliver a volume of air is measured in cubic feet per minute (cfm). cfm varies with atmospheric pressure. It also varies with the temperature and humidity of the air.

Technically, air compressor manufacturers calculate standard cubic feet per minute (scfm) as cfm at sea level with 68 degrees F air at 36% relative humidity. Scfm ratings are given at a specific pressure (for example) 3.0 scfm at 90 psi. If you reduce pressure, scfm goes up, and vice versa. I would recommend a model rated at about 4.9 cfm @90 psi The cfm and psi ratings are important because they will determine what a compressor is capable of doing.

The most important thing to determine when choosing a compressor is to make sure it can supply the amount of air and the pressure that your tires need. Many applications in garages and shops (like air tools) don't require 125 max psi, so they have a regulator to adjust the air. It may be necessary to increase this setting to inflate the tires.

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Wednesday, December 17, 2008

What's best, gas or diesel engine?

Dear Mark,
I sold my 24' Class C motorhome and am shopping for something newer and more efficient, also larger. I'm tending toward the Class B+ Phoenix Cruiser, 27' with two slides. It comes as either gasoline or diesel. I've been told the additional cost for a diesel engine outweighs any gas mileage benefit unless you keep the rig for many years. But I also wonder if other things have been factored in, such as, cost of engine maintenance, cost differential for the fuel type (as gasoline prices rise, will diesel rise at the same rate, slower, faster? What about bio diesel? Is there a re-sale advantage to either one?

I haven't found a discussion of these issues anywhere yet. The dealer I've been working with just gave me the answer above... the diesel is not cost-effective unless kept for many years. I'm an older, single woman, wanting to do some touring with my dog for the next two years or so. I'm expecting various friends to link up for certain legs of the trip. I will appreciate good guidance.

Mark says:
Gas versus diesel is an age old discussion and one that often times gets heated. If asked this question several years ago I would have responded similar to the salesperson because the cost of a diesel model over a gas model was quite significant. Today's RV's offer many gasoline models in the same price range as many diesel products, mainly due to advances in the chassis itself driving the prices upward.

What I can tell you is a diesel will last longer than a gasoline engine so if you plan to keep the RV for a long time it would be worth the investment. I have no idea what is going to happen with the types of fuel or the cost difference between gas and diesel.

Maintenance wise, it used to be that a diesel required less, keeping in mind there are more filters, etc., on a diesel. But nowadays gas engines can go upwards of 100,000 miles before a tune up with nothing more than routine oil changes, air filters, etc.

This probably doesn't help much. If you want some other opinions, I recommend you go to the RVtravel.com forum and post this same question in the appropriate forum. You are sure to get many responses.

Thursday, November 27, 2008

This travel companion can keep you sane, save your marriage

What weighs 15 ounces; is the size of a deck of cards and could possibly save an RVer's marriage? Let me give you a scenario. You’re driving your 35-foot RV on a congested four lane highway during rush hour, somewhere you've never been before and your better half is your navigator. You miss your exit and now you need to go 25 miles out of your way to get back on the correct route, arguing about whose fault it was the whole time. Sound familiar?

Now, let’s see what we can do to fix this problem. You’re driving your RV on a congested four lane highway, during rush hour, somewhere you have never been before and your new Global Positioning System (GPS) is your navigator. The unique, turn-by-turn, voice prompt feature instructs you to turn right in eight tenths of a mile. You don’t miss your exit; you don’t need to go 25 miles out of your way and your marriage remains intact.

In the past, whenever my wife Dawn and I would take a trip in the RV, I would print the driving directions from a trip planning website. Then, as we traveled, she would inform me of when and where we would make any changes in our route. Needless to say we missed turns, took wrong exits and on more than one occasion there were those last second, white knuckle lane changes: if you’ve been RVing for a while you know what I’m talking about.

I FINALLY DECIDED to take advantage of modern day technology and purchase a GPS system. All I can say is I should kick myself for waiting so long to do it. The more I learned about these GPS systems the more fascinated I was with their capabilities. Most come pre-programmed with detailed maps, automatic trip routing, voice-prompted turn-by-turn directions along your route, and easy-to-follow touch screen displays, which is exactly what you want when you’re traveling in an RV. If you get a text-to-speech feature the GPS actually calls out the turns you need to make, so you can keep your eyes where they need to be, on the road. If you miss a turn the GPS system automatically recalculates the quickest way to get back on the correct route.

Other features we liked about the GPS are the Points of Interest (POI) like, restaurants, shopping centers and tourist attractions. In addition to all of these features the GPS model we purchased includes a built in MP3 player and a JPEG picture viewer too.

I don’t know about you, but driving an RV in places you've never been before can be nerve-racking at times, especially if you're navigating the old school way, using a map. I am sometimes a little slow to change to the latest technology, but getting a GPS system to help navigate the RV is the best thing I’ve done since switching from dial-up to high speed internet service. This truly is a great way to make traveling in your RV less stressful. And, who knows, it might just result in a happier marriage, too!

A final note: I still print the route from a trip planning website and keep my maps next to the drivers seat, just in case!

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Tuesday, November 18, 2008

Must RV's electrical converter be on at all times?

Dear Mark,
I live year round in a large 5th wheel trailer and I am plugged in at all times. I hear the battery charger kicking in from time to time and the humming of the converter. Do I need to have the converter on at all times? Is it on only to charge the batteries? The manuals are the pits and I am really trying to know all about converters. The more questions I ask from different sources the more answers I get.

Mark:
The converter in your RV basically does two jobs.
1) When you are plugged into electricity it converts a portion of the 120 volts coming into the RV down to 12 volts so all of the 12 volt devices like overhead lights and fan motors will operate without draining the RV battery.
2) It has a battery charger built in the converter to keep the RV battery charged (topped off).

The noise you are hearing is most likely the fan on the converter. The converter gets warm when it is on so the manufacturer adds a fan to help keep it cool. Some are very noisy. You DO NEED the converter on when you are plugged in. If the converter wasn't on, or wasn't operating properly you would run the RV battery down because you are using the 12-volt appliances and devices.

Some older RV converters charge the batteries at a constant rate and will continue to charge the batteries when they are fully charged. This can result in the battery or batteries losing water, so battery maintenance and inspections are important when you have the RV plugged in for long periods of time. Newer converters have three stage chargers that know when the battery is fully charged and at that point only provide a float charge (less charge) to prevent overcharging conditions.

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Thursday, November 6, 2008

How to troubleshoot problems with your RV's 12-volt system

If you've been RVing for any amount of time you already know that a most of the devices and accessories in your motorhome, trailer or other RV operates on 12-volt DC power. Twelve-volt DC (or direct current) is supplied by the RV batteries. DC electricity flows in one direction, from negative to positive. Twelve-VDC electricity is stored in the RV batteries and supplies power for components, devices and appliances that operate on 12-volts.

These devices include overhead lights, the water pump, vent fans, furnace fan, range hood fan, LP gas leak detectors, stereos, 12-volt TVs and the refrigerator when it's operating in the LP gas mode. When camping you rely on these 12-volt items to operate properly, especially if you're dry camping without hook-ups. So what do you do when one of these 12-volt items quit working?

For the sake of an example let's say that we are dry camping and our 12-volt water pump quits working.

I am convinced that just about anybody is capable of troubleshooting a 12-VDC problem, and in many cases repairing the problem without it ruining a camping trip. For starters you'll need a couple of simple tools to assist you in troubleshooting your RV’s 12-volt electrical system.

1). An inexpensive 12-volt test light.

2). A multi-meter that can test for DC power.

Both of these are available at local auto parts stores. You should also keep some electrical tape, various size wire nuts, 12-volt light bulbs and 12-volt fuses on hand. Check the amperage of the fuses used in the power distribution box and keep an assortment. If you're aware of any inline fuses used on any of the 12-volt devices keep these on hand too.

Now, try to determine the last time the water pump actually worked. Did you leave the RV for a period of time with the pump on? Is there water in the fresh water holding tank? Were you working on or around something else that could have affected the operation of the water pump? Try to think of all possible scenarios. Something might jar your memory resulting in a quick fix to the problem.

If not, the first step is to verify that the coach battery or batteries are charged enough to supply power to these 12-volt items. There are a couple of ways to perform a quick test on the coach batteries. You can use the monitor panel to check their condition. For an accurate reading, make sure the RV is not plugged into electricity and turn on a couple of overhead lights to place a small load on the battery. Check the reading at the monitor panel. (If you check the reading at the monitor panel when the RV is plugged in to electricity it will give you fully charged reading) A more accurate method is to test the battery with a multi-meter. Set the meter to read 12-VDC and place the negative test probe on the negative battery terminal and the positive test probe on the positive battery terminal. A fully charged battery will read in the range of 12.6 to 12.7 volts. If it reads less than 12-volts it is below a 50 percent state of charge and will need to be charged.

IF THE BATTERY IS FULLY CHARGED, the next step is to make sure that any battery disconnect switch for the coach battery is turned on. If the battery disconnect switch is on, verify that other 12-volt devices in the RV are operating properly. If there is 12-volt power to the interior of the RV you need to check the fuse for the water pump in the power distribution center. Determine which fuse is for the water pump (fuses are normally labeled) and find a suitable ground for the 12-volt test light. Test both sides of the fuse for 12-volt power. If the test light only lights on one side of the fuse replace it with the proper size fuse and try the water pump again. If there was power at both sides of the fuse check for 12-volts at the water pump switch. If there is voltage, and the switch is operating properly check the water pump wiring for an inline fuse.

Find a good ground for the 12-volt test light and probe the wire on both sides of the fuse. If there is only power on one side of the fuse replace it with the proper size fuse and test the pump again. If there is power on both sides of the fuse check the water pump wiring connections at the wire nuts. It's possible for connections to come loose due to excessive vibration. Correct any loose connections and try the pump again. If the pump still doesn't work feel the motor to see if it is hot to the touch. If the motor is hot, a thermal breaker may have been triggered. Allow the pump time to cool off and see if it re-sets itself.

If you complete all of these tests and there is 12-volt DC power coming to the water pump motor, and it still doesn't come on, chances are the water pump is bad and it will need to be replaced.

Troubleshooting a 12-volt electrical problem in your RV is not that difficult. Follow the logical path of the device you are troubleshooting and see if you can determine where the problem is. It might be possible for you to save your well deserved vacation, some money and a trip to the RV dealership too.

Note: If you don't feel comfortable performing your own maintenance or troubleshooting the 12-volt electrical system, take your RV to a reputable repair center to have it checked out and repaired.

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.

Wednesday, October 29, 2008

Tips to make your RV fridge run more efficiently


If an RV refrigerator isn't running efficiently, in many cases it's something the owner did that affected its performance.

We can help the refrigerator do a better job. First and foremost, the RV must be fairly level for the refrigerator to operate properly. Older RV refrigerators required more precise leveling, but even newer models must be close to level for optimum performance. Over time, a cooling unit operated out of level will be permanently damaged. Traveling with the refrigerator operating will not cause problems because the liquids and gases in the cooling unit are constantly moving around. They don't collect and stay in areas of the cooling unit like they can in a stationary, out of level refrigerator.

The initial cool down process can take four to six hours. You should turn the refrigerator on the day before you plan to leave. When you put in the food, make sure it's already cold. Frozen food should already be frozen. Putting cold food in the refrigerator, rather than adding warm food, makes for less work for the refrigerator. One common mistake is to over pack a refrigerator. There must be space between the foods to allow for air to circulate throughout the compartment. On most RV trips, you will have access to a store to add to your food supply. So two to three day's worth should be enough.

To assist with air circulation you can purchase an inexpensive, battery operated refrigerator fan. Put the batteries in and place the fan in the front of the refrigerator compartment blowing up. Cold air drops and warm air rises. The fan will improve the efficiency by circulating the air and it will reduce the initial cool down time by half.

The heat created by the cooling process is vented behind the refrigerator. Air enters through the outside lower refrigerator vent and helps to draft the hot air out through the roof vent. Periodically inspect the back of the refrigerator and the roof vent for any obstructions like bird nests, leaves or other debris that might prevent the heat from escaping.

TO KEEP THE REFRIGERATOR OPERATING EFFICIENTLY in the LP gas mode, perform some routine maintenance. Remove the outside lower vent cover to access the back of the refrigerator. With the refrigerator turned off, ensure all connections are clean and tight. Turn the refrigerator on in the LP gas mode and look at the flame. If it's burning poorly, or is yellow-colored, or if the refrigerator isn’t operating properly in the gas mode it’s possible that the baffle inside the flue is covered with soot.

Soot, rust and other debris can fall down and obstruct the burner assembly. When this happens it's necessary to clean the flue and the burner assembly. Turn the refrigerator off again and locate the burner. Directly above the burner is the flue. The baffle is inside the flue. Wear a pair of safety glasses and use an air compressor to blow air up into the flue. After the flue is clean use the compressed air to remove any debris from the outside refrigerator compartment. Now, turn the refrigerator on in the LP gas mode to make sure it is working properly. Look for the bright blue flame. For a thorough cleaning of the flue and baffle it will be necessary to have your RV dealer do it for you. While it’s there have them to do an LP gas pressure test, too.

Another good idea is to install a 12 volt, thermostatically controlled refrigerator vent fan at the back of the refrigerator or at the top of the roof vent to assist with drafting the hot air away from the refrigerator. If you are mechanically inclined these fans are fairly easy to install, or you can have your RV dealer install one for you. Either way it’s worth it. The fan removes the heat built up behind the refrigerator improving the refrigerators performance by up to 40 percent.

Outside temperature affects the operation and efficiency of your RV refrigerator. When it’s cold outside you can lower the temperature setting and when it’s hot you can raise the setting. Some refrigerators are preset by the manufacturer. Extremely hot weather will directly affect the refrigerators efficiency. When it’s really hot outside try parking your RV with the refrigerator side in the shade. Periodically inspect and clean the refrigerator door gaskets. Check them for a good seal. Place a dollar bill behind the seal and close the door. It should stay there and not drop. When you try to pull it out there should be some resistance felt. Do this in several different places and have any damaged seals replaced.

Try to limit the amount of times you open the refrigerator or freezer doors and the length of time you leave the doors open. Every time the door is opened it loses a few degrees of heat. On a hot summer day it won’t take long to lose all of its cooling capacity. Last but not least you should always have a thermostat in the food compartment. Food will begin to spoil at temperatures above 40 degrees.

RV absorption refrigerators do a great job for RVers. They will do an even better job, and last longer, if we apply these simple tips to make their job easier and less demanding.

Learn more about using your RV and its operation with Mark Polk's best-selling DVDs, books and eBooks.