Overloading your RV is likely the leading cause of tire failure. Poor weight distribution and using all of the storage space offered on today's recreational vehicles result in tire overloads.
The only way to learn if your RV is too heavy or loaded improperly is to have the it weighed on platform scales while fully loaded. Load it with everything you plan to take on a trip including passengers, cargo, fuel, full fresh water and propane tanks. If you tow something behind the RV take it to the scales, too. It's possible to weigh the RV and not exceed the GVWR, GAWR or GCWR, but still exceed the tire ratings. This is why you must weigh each axle end separately to determine if tire ratings are exceeded and if the loaded weight is properly distributed.
Under inflated tires run a close second to overloading as a leading cause of tire failure. The load rating for a tire is only accurate if the tire is properly inflated. Under inflated tires cause extreme heat build up that leads to tire failure. The appearance of the tire may look normal but the internal damage can cause the tire to fail without warning.
Tires can lose up to two pounds of air pressure per month. If you don't check your tires for three or four months they could be seriously under inflated.
Ideally you should check tire inflation every day you move or drive your RV and adjust if necesssary. If you can't get into the habit of doing it on a daily basis, then at least check all tires weekly at a minimum when you're traveling.
Always check tires when they are cold, before moving the RV. Invest in an accurate inflation pressure gauge. Check all tires and adjust pressure according to the manufacturer's recommendation. Do no exceed the maximum pressure ratings found on the tires sidewall. Never check inflation pressure when the tires are hot: you will get a higher-pressure reading and if you let some air out they will be under inflated when they are cold. If you have dual wheels, add extension hoses to the valve stems to make checking tire pressure easier. A word of caution, if you add extension hoses you must replace the rubber valve stems with all steel valve stems. The added weight of the extension hoses can cause rubber stems to leak air resulting in under inflation.
OZONE IN THE AIR and UV rays from the sun shorten the life of your tires. It is not uncommon to see RV tires with low mileage and plenty of tread ruined by the damaging effects of ozone and UV rays. Ozone causes tires to dry rot and deteriorate. UV rays from the sun make it happen quicker. This is especially true of the tires sidewall. Inspect your tires for cracks in the sidewalls. If you notice any damage have them inspected by a professional. Two ways to protect your tires from these elements are to keep them covered to block out the sunlight when not in use. For long-term storage, remove the tires and store them in a cool dry place away from the sunlight. I also recommend that you place something like a piece of wood between the ground and the tires. Be sure that whatever you use is larger then the footprint of the tire.
The age of your tires is another factor that contributes to tire failure. I learned this the hard way. I bought an early model Jeep CJ7 to tow behind our motorhome. After completely restoring the vehicle we were ready to try it out. The tires appeared in excellent condition. There were no signs of damage from the sun and little tread wear. We towed the Jeep from North Carolina to Florida and from there to Colorado and back to North Carolina with no problems. Shortly after that we towed it to Pennsylvania. A couple hundred miles into the trip a front tire blew out, damaging the inner fender, shock absorber and below the door. I replaced the tire with the spare and within another 100 miles the spare blew out resulting in more damage. After buying a new tire, we took the Jeep to a tire store to have the other tires replaced. The technician explained that the tires were nine years old and even though they looked in good shape they could not handle the stress put on them. He explained that all tires manufactured in the United States have a DOT number. The number on my tires was on the inside sidewalls. The last three or four digits in the number identify how old the tire is. Older tires used three digits. The first two identify the week of the year that the tire was built and the third identifies the year. Newer tires use four digits. So 3202 is the 32nd week of the year, and 02 is the year 2002. If you question the age of your tires, especially on a used RV, and you can't find the DOT number have them inspected by a qualified tire center.
Have you ever neglected rotate your tires and then one day suddenly notice that the front ones are worn out while the rear one look fine? Even out the wear, and extend the life of your tires by having the tires on your vehicle rotated on a regular basis.
Tuesday, June 9, 2009
Tuesday, May 19, 2009
Dead RV refrigerator "burped" and then works again
Dear Mark,
When our fridge died while at an RV show, we were told it would cost $1,000 to replace it. We travel on a budget (working as we go) and we're going on a big far north four month tour starting in June. A chance conversation with an RVer led us to "burping" the fridge, lying it on its side before bringing it back upright. We were happy campers to see it working again. But I have since been told it may only be a temporary fix. What do you know about this process and have you heard how long it lasts?
Mark says:
Back in the '70s we would burp RV refrigerators frequently. Older RV refrigerators (pre-early '80s) required precise leveling to work properly. If the unit wasn't level the flow of ammonia in the coils would get vapor locked and the refrigerator wouldn't cool. You would remove the refrigerator and (burp it) turn it upside down for 24 hours. Sometimes it worked, sometimes it didn't.
Newer RV refrigerators don't require as precise leveling as older models. If it's within half a bubble on the level it will operate okay. If you experience a problem with a newer model you can usually turn the refrigerator off a couple hours, make sure the RV is level and turn it back on. If a refrigerator is operated out of level (more than half a bubble) for extended periods the coolant can pool (stop moving) and overheat, resulting in the cooling unit failing.
There are some tell-tale signs of a failing cooling unit. If you smell ammonia in or around the refrigerator the cooling unit is bad and will need to be replaced. If the refrigerator makes loud noises during the initial cool down process the cooling unit may be going bad.
If you burped the unit it's possible that it removed an obstruction that was restricting the flow and now it is okay. If it has other symptoms like I mentioned, or was operated out of level, it will probably need to be replaced. I wish I could tell you more, but it's difficult to say what the outcome will be.
DVD: Travel Trailer/Fifth Wheel 101
If you just bought a travel trailer or 5th wheel trailer, you'll need to know how to operate it. The onboard systems -- electrical, water, LP gas and waste -- are often confusing to new owners. This one hour DVD hosted by Mark Polk provides an excellent understanding of how a towable RV's systems work and how to operate them safely. Learn more order.
When our fridge died while at an RV show, we were told it would cost $1,000 to replace it. We travel on a budget (working as we go) and we're going on a big far north four month tour starting in June. A chance conversation with an RVer led us to "burping" the fridge, lying it on its side before bringing it back upright. We were happy campers to see it working again. But I have since been told it may only be a temporary fix. What do you know about this process and have you heard how long it lasts?
Mark says:
Back in the '70s we would burp RV refrigerators frequently. Older RV refrigerators (pre-early '80s) required precise leveling to work properly. If the unit wasn't level the flow of ammonia in the coils would get vapor locked and the refrigerator wouldn't cool. You would remove the refrigerator and (burp it) turn it upside down for 24 hours. Sometimes it worked, sometimes it didn't.
Newer RV refrigerators don't require as precise leveling as older models. If it's within half a bubble on the level it will operate okay. If you experience a problem with a newer model you can usually turn the refrigerator off a couple hours, make sure the RV is level and turn it back on. If a refrigerator is operated out of level (more than half a bubble) for extended periods the coolant can pool (stop moving) and overheat, resulting in the cooling unit failing.
There are some tell-tale signs of a failing cooling unit. If you smell ammonia in or around the refrigerator the cooling unit is bad and will need to be replaced. If the refrigerator makes loud noises during the initial cool down process the cooling unit may be going bad.
If you burped the unit it's possible that it removed an obstruction that was restricting the flow and now it is okay. If it has other symptoms like I mentioned, or was operated out of level, it will probably need to be replaced. I wish I could tell you more, but it's difficult to say what the outcome will be.
If you just bought a travel trailer or 5th wheel trailer, you'll need to know how to operate it. The onboard systems -- electrical, water, LP gas and waste -- are often confusing to new owners. This one hour DVD hosted by Mark Polk provides an excellent understanding of how a towable RV's systems work and how to operate them safely. Learn more order.
Thursday, May 14, 2009
Tips on how to care for the roof of your RV
One of the most neglected areas on your RV is the roof. If you don't keep it clean and inspect its seams on a regular basis you could end up with a big repair bill for water damage. Most of today's RVs use some type of rubber or vinyl roofing material. Here are some things you can do to extend the life of your RV roof.
Safety first!
Be extremely careful whenever you work on your RV roof. You can be seriously injured from a fall. To properly clean and inspect your roof for any damage or potential water leaks you need to climb onto it. Some roofs are more structurally sound than others. It may be necessary to use a couple of 2X4 pieces of plywood or particle board to help distribute your weight between the roof rafters. Regardless of its structural integrity, however, you should walk lightly and be careful.
Rubber and vinyl roofing on an RV are both good, but without routine preventive maintenance they will not last as long as they could.
There are different manufacturers of rubber and vinyl roofs. They provide different instructions for cleaning and maintaining their products. What I'll concentrate on here is what applies to most rubber and vinyl roofing material used on RVs.
Rubber and vinyl roofs should be cleaned and inspected several times a year. Depending on where you park or store your RV its roof may need to be cleaned and inspected more often. Regardless of the type of rubber or vinyl roof you have, NEVER use any cleaners or conditioners that contain petroleum solvents, harsh abrasives or citrus ingredients. These cleaners can cause permanent damage to rubber or vinyl surfaces.
Most manufacturers of rubber roofs recommend you use a medium bristle brush and a non-abrasive cleaner. For light cleaning you can use warm water and a mild detergent like Dawn dish washing liquid. For more difficult cleaning, and to condition and protect the roof, use a commercial cleaning product designed specifically for the roofing material of your RV. Check with your RV dealer for sealants that are compatible with your roofing material.
Hard-to-clean areas like stubborn stains caused by leaves, sap, mold or mildew may require a second treatment. Use caution to prevent the cleaners from getting on the sides of the RV. Always rinse the sides, front and back of your RV before and after rinsing the roof to prevent cleaners from streaking or damaging the finish on your RV sidewalls.
Cleaning the roof is only part of maintaining it. Every time you clean it you need to inspect the sealants around all of the openings and the seams. Water will take the path of least resistance and will find even the smallest opening. Thoroughly inspect the roof sealants for potential leaks and reseal any areas of the roof seams and around openings where you suspect a leak.
Routine cleaning, inspecting and sealing your RV roof can add years to the life to the roof and help prevent costly repairs caused by water damage.

Get headline RV news from Twitter
Keep up with the latest in RV news and information at our new RV Travel headline service at Twitter.com. Plus, you'll be the first to get an alert about each new issue of the weekly RVtravel.com newsletter. Go there now.
Safety first!
Be extremely careful whenever you work on your RV roof. You can be seriously injured from a fall. To properly clean and inspect your roof for any damage or potential water leaks you need to climb onto it. Some roofs are more structurally sound than others. It may be necessary to use a couple of 2X4 pieces of plywood or particle board to help distribute your weight between the roof rafters. Regardless of its structural integrity, however, you should walk lightly and be careful.
Rubber and vinyl roofing on an RV are both good, but without routine preventive maintenance they will not last as long as they could.
There are different manufacturers of rubber and vinyl roofs. They provide different instructions for cleaning and maintaining their products. What I'll concentrate on here is what applies to most rubber and vinyl roofing material used on RVs.
Rubber and vinyl roofs should be cleaned and inspected several times a year. Depending on where you park or store your RV its roof may need to be cleaned and inspected more often. Regardless of the type of rubber or vinyl roof you have, NEVER use any cleaners or conditioners that contain petroleum solvents, harsh abrasives or citrus ingredients. These cleaners can cause permanent damage to rubber or vinyl surfaces.
Most manufacturers of rubber roofs recommend you use a medium bristle brush and a non-abrasive cleaner. For light cleaning you can use warm water and a mild detergent like Dawn dish washing liquid. For more difficult cleaning, and to condition and protect the roof, use a commercial cleaning product designed specifically for the roofing material of your RV. Check with your RV dealer for sealants that are compatible with your roofing material.
Hard-to-clean areas like stubborn stains caused by leaves, sap, mold or mildew may require a second treatment. Use caution to prevent the cleaners from getting on the sides of the RV. Always rinse the sides, front and back of your RV before and after rinsing the roof to prevent cleaners from streaking or damaging the finish on your RV sidewalls.
Cleaning the roof is only part of maintaining it. Every time you clean it you need to inspect the sealants around all of the openings and the seams. Water will take the path of least resistance and will find even the smallest opening. Thoroughly inspect the roof sealants for potential leaks and reseal any areas of the roof seams and around openings where you suspect a leak.
Routine cleaning, inspecting and sealing your RV roof can add years to the life to the roof and help prevent costly repairs caused by water damage.
Get headline RV news from Twitter
Keep up with the latest in RV news and information at our new RV Travel headline service at Twitter.com. Plus, you'll be the first to get an alert about each new issue of the weekly RVtravel.com newsletter. Go there now.
Thursday, May 7, 2009
How to tow an RV dinghy four-wheels down with a motorhome
I get asked many questions about towing a vehicle behind a motorhome, but perhaps the most common is “How do you know what vehicles can be towed with four-wheels on the ground?” Here are some tips.
You basically have three options when it comes to towing a vehicle behind your motorhome. You can tow the vehicle with all four-wheels up using a car trailer, with two-wheels up using a tow dolly, or with all four-wheels down.
In recent years towing with all four-wheels down, using a tow bar, has become more popular. Some of the reasons are the ease of hitching and unhitching, not having to deal with a trailer and that more automobile manufacturers are building vehicles that can be towed with four-wheels on the ground without modifications.
What Vehicles Can I Tow With Four-Wheels Down?
Some manufacturer approved vehicles can be towed four-wheels down without any modifications to the drive-train or transmission, but many more require some type of modification to tow it with all four-wheels on the ground.
Many vehicles with automatic transmission cannot be towed with all four-wheels down unless it is four-wheel drive, and even then it requires a transfer case that can be shifted into neutral. Front wheel drive vehicles with manual transmissions and most four-wheel drive vehicles with a manual transfer case are among the best choices for towing with all four-wheels down. Even if you have a vehicle that can be towed with all four-wheels down it’s quite possible that it will have towing speed and/or mileage restrictions. So where do we start?
Start by reading your vehicle owner’s manual to determine if the vehicle can be towed without any drive-train modifications. If the vehicle is approved by the manufacturer to be towed with all four-wheels down the owner’s manual will provide specific instructions on the proper procedures. If the manual does not provide specific instructions about towing with all four- wheels down check with the vehicle manufacturer. Your vehicle warranty could be voided from damage caused by towing a vehicle and not following the manufacturer’s guidelines. Do not rely on what a vehicle salesperson tells you. Almost all vehicles approved to be towed with all four- wheels down will include this information in the vehicle owner’s manual.
If you don’t already have a vehicle to tow a good resource to check on what vehicles can be towed with all four-wheels down is the annual “Dinghy Towing Guide” available at RVbookstore.com. Keep in mind that this is only a guide and it is your responsibility to make absolutely sure the vehicle you are considering towing can be towed with all four-wheels down, with no drive-train modifications, before you make a purchase or actually tow the vehicle.
The Dinghy Towing Guide includes manufacturer approved vehicles for towing without modifications that can be towed at speeds of at least 55 MPH and for distances of at least 200 miles without any special procedures. Pay particular attention to any speed or distance restrictions that could ultimately affect your vehicle warranty. Also pay attention to the restrictions and special instructions listed in the footnotes. The guide lists other valuable information like vehicle curb weights, fuel economy and base retail prices. Keep in mind the lighter the vehicle the better it is. It is easy to exceed a motorhomes receiver weight rating and the Gross Combined Weight Rating (GCWR). Note also that some models listed in their four- wheel drive version can be towed without modifications, but their two-wheel drive version of the same model cannot be towed with four-wheels on the ground.
Be sure to follow any special towing instructions or procedures found in the vehicle owner’s manual. You might be required to remove a certain fuse before you tow the vehicle, or to stop towing after so many miles and start the vehicle to allow drive train components to be lubricated. Following any and all special instructions can save you money and protect the vehicle warranty.
There are many reasons why some vehicles are not approved by the manufacturer to be towed with all four-wheels down. It may be that the vehicle will not track or follow the motorhome properly, or maybe a component in the drive-train could be damaged, and sometimes it is because of liability and warranty concerns. Another reason is the expense involved for a manufacturer to test and approve vehicles for towing with all four-wheels down.
The good news is, in many cases where vehicles are not approved by the manufacturer to be towed with all four-wheels down they can still be towed in this method by adding some type of aftermarket accessory. The most common problem is when the engine is not running components in the drive-train that require lubrication are not being lubricated. Towing a vehicle like this can result in thousands of dollars worth of damage, and/or possibly overheat and catch on fire.
There are specialty aftermarket products and modifications available such as drive shaft disconnects and/or transmission lube pumps that can be added so a vehicle is mechanically capable of being towed without damaging the drive-train.
If the vehicle you want to tow falls in the 20 percent that cannot be modified for towing, you still have the option of using a tow dolly or a car trailer. All vehicles can be towed on a car trailer, as long as you don’t exceed weight ratings, and most front wheel drive vehicles can be towed with a tow dolly.
For more in-depth information on towing check out my DVD Towing Behind your Motorhome.
You basically have three options when it comes to towing a vehicle behind your motorhome. You can tow the vehicle with all four-wheels up using a car trailer, with two-wheels up using a tow dolly, or with all four-wheels down.
In recent years towing with all four-wheels down, using a tow bar, has become more popular. Some of the reasons are the ease of hitching and unhitching, not having to deal with a trailer and that more automobile manufacturers are building vehicles that can be towed with four-wheels on the ground without modifications.
What Vehicles Can I Tow With Four-Wheels Down?
Some manufacturer approved vehicles can be towed four-wheels down without any modifications to the drive-train or transmission, but many more require some type of modification to tow it with all four-wheels on the ground.
Many vehicles with automatic transmission cannot be towed with all four-wheels down unless it is four-wheel drive, and even then it requires a transfer case that can be shifted into neutral. Front wheel drive vehicles with manual transmissions and most four-wheel drive vehicles with a manual transfer case are among the best choices for towing with all four-wheels down. Even if you have a vehicle that can be towed with all four-wheels down it’s quite possible that it will have towing speed and/or mileage restrictions. So where do we start?
Start by reading your vehicle owner’s manual to determine if the vehicle can be towed without any drive-train modifications. If the vehicle is approved by the manufacturer to be towed with all four-wheels down the owner’s manual will provide specific instructions on the proper procedures. If the manual does not provide specific instructions about towing with all four- wheels down check with the vehicle manufacturer. Your vehicle warranty could be voided from damage caused by towing a vehicle and not following the manufacturer’s guidelines. Do not rely on what a vehicle salesperson tells you. Almost all vehicles approved to be towed with all four- wheels down will include this information in the vehicle owner’s manual.
If you don’t already have a vehicle to tow a good resource to check on what vehicles can be towed with all four-wheels down is the annual “Dinghy Towing Guide” available at RVbookstore.com. Keep in mind that this is only a guide and it is your responsibility to make absolutely sure the vehicle you are considering towing can be towed with all four-wheels down, with no drive-train modifications, before you make a purchase or actually tow the vehicle.
The Dinghy Towing Guide includes manufacturer approved vehicles for towing without modifications that can be towed at speeds of at least 55 MPH and for distances of at least 200 miles without any special procedures. Pay particular attention to any speed or distance restrictions that could ultimately affect your vehicle warranty. Also pay attention to the restrictions and special instructions listed in the footnotes. The guide lists other valuable information like vehicle curb weights, fuel economy and base retail prices. Keep in mind the lighter the vehicle the better it is. It is easy to exceed a motorhomes receiver weight rating and the Gross Combined Weight Rating (GCWR). Note also that some models listed in their four- wheel drive version can be towed without modifications, but their two-wheel drive version of the same model cannot be towed with four-wheels on the ground.
Be sure to follow any special towing instructions or procedures found in the vehicle owner’s manual. You might be required to remove a certain fuse before you tow the vehicle, or to stop towing after so many miles and start the vehicle to allow drive train components to be lubricated. Following any and all special instructions can save you money and protect the vehicle warranty.
There are many reasons why some vehicles are not approved by the manufacturer to be towed with all four-wheels down. It may be that the vehicle will not track or follow the motorhome properly, or maybe a component in the drive-train could be damaged, and sometimes it is because of liability and warranty concerns. Another reason is the expense involved for a manufacturer to test and approve vehicles for towing with all four-wheels down.
The good news is, in many cases where vehicles are not approved by the manufacturer to be towed with all four-wheels down they can still be towed in this method by adding some type of aftermarket accessory. The most common problem is when the engine is not running components in the drive-train that require lubrication are not being lubricated. Towing a vehicle like this can result in thousands of dollars worth of damage, and/or possibly overheat and catch on fire.
There are specialty aftermarket products and modifications available such as drive shaft disconnects and/or transmission lube pumps that can be added so a vehicle is mechanically capable of being towed without damaging the drive-train.
If the vehicle you want to tow falls in the 20 percent that cannot be modified for towing, you still have the option of using a tow dolly or a car trailer. All vehicles can be towed on a car trailer, as long as you don’t exceed weight ratings, and most front wheel drive vehicles can be towed with a tow dolly.
For more in-depth information on towing check out my DVD Towing Behind your Motorhome.
Thursday, April 2, 2009
Why can't a motorhome be backed while towing a dinghy?
Dear Mark,
I have purchased several books and eBooks from RVbookstore.com, but I can’t find the answer to my burning question. In your eBook The Complete Guide to Dinghy Towing you say to never back up a motorhome when pulling a dinghy. My question is: You see many motorhomes pulling boats. If you can’t back up a toad, how do boaters back up to launch their boats? --Jim Walker
Dear Jim,
The reason you can back a boat trailer, but not a dinghy (car or other vehicle), is that the boat trailer doesn't have a set of steering front wheels.
A while back an engineer at Blue Ox experimented backing several towed vehicles. The results weren't good. One person would drive the motorhome and another would attempt to steer the front wheels of the toad. The problem was, in every test, the front wheels would unexpectedly turn drastically to one side making the steering wheel violently spin out of control. If a person has their hands or arm caught in the steering wheel the results could be a broken finger, hand or arm. Even when they attempted to back straight back the wheels would turn, and it was with other manufacturers tow bars too. You should never attempt to back a toad!
Here is how the engineer explained it:
"The reason this happens is not the tow bar but rather the caster angle in the front end of the towed vehicle. Caster is the forward tilt of the steering axis versus vertical. It provides steering stability, steering returnability and cornering ease. In reverse, the caster angle makes the wheels want to turn around the other direction like "casters" on your office chair or shopping cart. We all know they can't turn all the way around on a car, but they will turn off to the side as far as the steering mechanism will let them.
This is virtually undetectable from the driver's seat in the motorhome making this a very scary situation. If you continue to back up, after the wheels have turned, the tires "scrub" or slide sideways causing damage to the tires. Other things caused by this are; severe stress to the steering components, suspension and towing system components."

Get headline RV news from Twitter
Keep up with the latest in RV news and information at our new RV Travel headline service at Twitter.com. Plus, you'll be the first to get an alert about each new issue of the weekly RVtravel.com newsletter. Go there now.
I have purchased several books and eBooks from RVbookstore.com, but I can’t find the answer to my burning question. In your eBook The Complete Guide to Dinghy Towing you say to never back up a motorhome when pulling a dinghy. My question is: You see many motorhomes pulling boats. If you can’t back up a toad, how do boaters back up to launch their boats? --Jim Walker
Dear Jim,
The reason you can back a boat trailer, but not a dinghy (car or other vehicle), is that the boat trailer doesn't have a set of steering front wheels.
A while back an engineer at Blue Ox experimented backing several towed vehicles. The results weren't good. One person would drive the motorhome and another would attempt to steer the front wheels of the toad. The problem was, in every test, the front wheels would unexpectedly turn drastically to one side making the steering wheel violently spin out of control. If a person has their hands or arm caught in the steering wheel the results could be a broken finger, hand or arm. Even when they attempted to back straight back the wheels would turn, and it was with other manufacturers tow bars too. You should never attempt to back a toad!
Here is how the engineer explained it:
"The reason this happens is not the tow bar but rather the caster angle in the front end of the towed vehicle. Caster is the forward tilt of the steering axis versus vertical. It provides steering stability, steering returnability and cornering ease. In reverse, the caster angle makes the wheels want to turn around the other direction like "casters" on your office chair or shopping cart. We all know they can't turn all the way around on a car, but they will turn off to the side as far as the steering mechanism will let them.
This is virtually undetectable from the driver's seat in the motorhome making this a very scary situation. If you continue to back up, after the wheels have turned, the tires "scrub" or slide sideways causing damage to the tires. Other things caused by this are; severe stress to the steering components, suspension and towing system components."
Get headline RV news from Twitter
Keep up with the latest in RV news and information at our new RV Travel headline service at Twitter.com. Plus, you'll be the first to get an alert about each new issue of the weekly RVtravel.com newsletter. Go there now.
Friday, March 27, 2009
Uneven towing laws, lack of driver knowledge cause accidents
I've always been an advocate for towing safety, whether it's towing a trailer or a vehicle behind a motorhome. One of the most controversial topics I've encountered is whether a vehicle towed behind a motorhome needs a supplemental braking system. I believe that if the state where you live has laws requiring a trailer over a certain weight to have brakes then the laws would also apply to a vehicle towed behind a motorhome. Another argument is that many state towing laws are antiquated and need to be updated. When some of these laws were written people weren't towing vehicles behind motorhomes.
The brakes on a motorhome are designed to stop the weight of that particular vehicle, not additional weight being towed. This additional weight adds a substantial increase to the distance required to stop safely. And, even if the motorhome is capable of stopping the vehicle, the added stress from the force on the tow bar and hitch when the vehicle doesn't have brakes can result in damage to the tow bar or separation from the hitch. Some motorhome chassis warranties are voided if you tow over a certain amount without a supplemental braking system.
I'll go even one step further. I am not a big fan of the federal government regulating things that individual states should control, but when it comes to trailer towing laws I do believe the laws should be the same for every state. Trailers need safety chains, lights, proper hitchwork and if it weighs over a certain amount it needs brakes, period! It makes no sense that a trailer would need brakes in one state but not in another state. Why do we need 50 different sets of guidelines and laws regulating the operation of a trailer?
AFTER ANALYZING A FIVE YEAR HISTORY of data collected through the National Highway Traffic Safety Administrations General Estimates System I discovered that on average there were 68,358 accidents involving passenger vehicles towing trailers per year. The average fatalities from accidents involving trailers are 446 per year. The average numbers of injuries from these accidents are 24,506 per year and the average instances of property damage resulting from these accidents are 43,405 per year. To me, this is unacceptable.
I would guess that most of these trailer related accidents involve small utility trailers, trailers used in construction and other businesses, horse trailers and of course boat and RV trailers, too. The bottom line is there is no excuse for these kinds of statistics. I see unsafe trailers on the road all the time, but the way I see it is in most cases it is a driver's lack of education or understanding of what is involved to safely and properly tow a trailer, regardless its type or size.
I think a good start to educating the consumer would be to standardize the laws and regulations regarding the operation of all trailers and vehicles being towed. It would simplify the process and answer questions that people have like:
1) What is required to be on the trailer i.e., safety chains, lights, break-away switch (with a charged battery)?
2) How much can a trailer/vehicle weigh before it needs brakes?
3) What type of hitchwork do I need?
Half of the battle to safe towing is using the proper equipment. The other half is enforcement. Law enforcement officers need to be trained on what the laws and requirements are for safe trailer towing and then enforce the laws.
There is no reason for over 68,000 accidents and more than 440 deaths a year involving vehicles towing trailers.
That's how I see it, how about you?
Learn how to tow a vehicle behind a motor home in an easy to understand way. RV expert Mark Polk shows you everything you need to know.
The brakes on a motorhome are designed to stop the weight of that particular vehicle, not additional weight being towed. This additional weight adds a substantial increase to the distance required to stop safely. And, even if the motorhome is capable of stopping the vehicle, the added stress from the force on the tow bar and hitch when the vehicle doesn't have brakes can result in damage to the tow bar or separation from the hitch. Some motorhome chassis warranties are voided if you tow over a certain amount without a supplemental braking system.
I'll go even one step further. I am not a big fan of the federal government regulating things that individual states should control, but when it comes to trailer towing laws I do believe the laws should be the same for every state. Trailers need safety chains, lights, proper hitchwork and if it weighs over a certain amount it needs brakes, period! It makes no sense that a trailer would need brakes in one state but not in another state. Why do we need 50 different sets of guidelines and laws regulating the operation of a trailer?
AFTER ANALYZING A FIVE YEAR HISTORY of data collected through the National Highway Traffic Safety Administrations General Estimates System I discovered that on average there were 68,358 accidents involving passenger vehicles towing trailers per year. The average fatalities from accidents involving trailers are 446 per year. The average numbers of injuries from these accidents are 24,506 per year and the average instances of property damage resulting from these accidents are 43,405 per year. To me, this is unacceptable.
I would guess that most of these trailer related accidents involve small utility trailers, trailers used in construction and other businesses, horse trailers and of course boat and RV trailers, too. The bottom line is there is no excuse for these kinds of statistics. I see unsafe trailers on the road all the time, but the way I see it is in most cases it is a driver's lack of education or understanding of what is involved to safely and properly tow a trailer, regardless its type or size.
I think a good start to educating the consumer would be to standardize the laws and regulations regarding the operation of all trailers and vehicles being towed. It would simplify the process and answer questions that people have like:
1) What is required to be on the trailer i.e., safety chains, lights, break-away switch (with a charged battery)?
2) How much can a trailer/vehicle weigh before it needs brakes?
3) What type of hitchwork do I need?
Half of the battle to safe towing is using the proper equipment. The other half is enforcement. Law enforcement officers need to be trained on what the laws and requirements are for safe trailer towing and then enforce the laws.
There is no reason for over 68,000 accidents and more than 440 deaths a year involving vehicles towing trailers.
That's how I see it, how about you?
Learn how to tow a vehicle behind a motor home in an easy to understand way. RV expert Mark Polk shows you everything you need to know.
Thursday, March 19, 2009
Keeping cool in your RV
Summer will be here soon and for RVers that not only means prime travel season is upon us, but so is the heat. If you ever walked inside an RV sitting in the direct sunlight, on a hot summer day, you know what I mean. Fortunately there are some simple things we can do to make our summer RV camping trips more pleasurable.•Strategically parking your RV to take advantage of any shade that is available, especially on the side where the refrigerator vent is located. Don’t be afraid to ask for a shady site when you check in at the campground. This will not only help cool the RV down, but your refrigerator and roof A/C will work much more efficiently.
•You can improve your air conditioners efficiency by keeping the A/C filters clean. In most cases you can wash the filters in warm soapy water, rinse thoroughly and allow them to dry before reinstalling. Another option is to clean the filters with a small hand held vacuum cleaner. I recommend you keep a new set of filters on hand in the event the old filters have seen better days.
•Use your patio awning and any window awnings to assist in cooling the RV down. In addition to the awnings use your window blinds or drapes to help keep the sun out and the cooler air in.
•Campground voltage can fluctuate, especially during the summer months when campers are placing a higher demand on campground electricity. You should monitor the voltage coming in to your RV with a digital voltmeter. If voltage drops below 105-volts or goes above 130-volts turn your appliances and electronic equipment off until proper voltage is restored.
Subscribe to:
Posts (Atom)