Wednesday, October 5, 2011

What you need to know about tow vehicle braking laws

Most U.S. States and Canadian Provinces have their own laws on the requirement for brakes on a towed trailer. The word trailer also applies to a vehicle being towed behind a motorhome. These laws are normally based on the amount of weight being towed. Not only is it illegal to exceed these weight limits without brakes, but your insurance company may not cover you in the event of an accident involving a trailer with no braking system. The most important reason is for your safety and the safety of others.

For a complete list of braking laws for the U.S. and Canada go to http://www.roadmasterinc.com/products/braking/map.html

The brakes on a tow vehicle or motor home are designed by the vehicle manufacturer to stop the weight of that particular vehicle, not the additional weight being towed behind it. This additional weight adds a substantial increase to the distance required to stop safely.

Travel trailers and 5th wheels come equipped with electric brakes and RV dealers educate the RV consumer on the requirements for adding an electronic brake control to the tow vehicle. Some pop-ups are ordered with brakes and some without. Again, this is often times based on the braking laws for the state you live in. My advice is if you’re going to purchase a pop-up get one that has brakes.

The real culprit for disregarding braking laws is a motorhome towing a vehicle behind it. Most people assume that because of the size of the motor home there is no need for a supplemental brake system on the towed vehicle and sometimes RV dealers fail to communicate the requirement for a supplemental braking system.

I for one was guilty of towing a vehicle without a braking system for quite some time. A close call while driving through a major city during rush hour suddenly educated me on how important it is.

ANOTHER THING THAT SURPRISES PEOPLE is how much the vehicle they’re towing actually weighs. Take your towed vehicle to a set of scales and have it weighed. Make sure it has everything in it that will be in it when you are towing it. After you weigh it double check to make sure the receiver on the motorhome is rated to tow that amount of weight and that you aren’t exceeding any of the motor home weight ratings like the Gross Combined Weight Rating (GCWR). The GCWR is the maximum permissible weight of the fully loaded motor home and the fully loaded towed vehicle combined. Most RV chassis manufacturers base their GCWR on the assumption that a supplemental brake system is being used.

Regardless of the brake system that best suits your individual needs the important thing is that you have one. There are many reasons to have a braking system on your towed vehicle.

1) It’s the law
2) It can void your vehicle warranty
3) It can void your insurance
4) It will reduce wear and tear on RV brakes and other components
5) Liability

But, most importantly it SAFELY reduces the stopping distance and helps to protect you, your loved ones and the safety of others.

Thursday, September 29, 2011

Debunking Portable Air Compressors: They're not all up to the job

I think most RVers understand the importance of maintaining proper tire inflation pressure. The problem is if you wait until you’re on the road to check tire pressure the tires are too hot for correct evaluation. Checking the inflation pressure when you stop to refuel doesn’t make sense because you will get higher pressure readings and if you let air out the tires they are under-inflated when they are cold. Another problem is when you are at the campground, and you want to check the tire pressure, there is no available air support to do it.

This is why you might want to consider purchasing a portable air compressor. But, air compressors can be confusing to understand, especially if you are trying to find one that is capable of increasing the inflation pressure in large motorhome tires. Let’s start with some air compressor basics.

Air compressors have 3 main ratings associated with them, horsepower (HP), Cubic Feet per Minute (CFM) and Pounds per Square Inch (PSI). Understanding these 3 functions of an air compressor can help us select the right portable air compressor for the job.

We’ll start with horsepower. Unfortunately when it comes to air compressors manufacturers don’t do a great job of explaining it to the consumer, almost to the point some would consider false advertising. Manufacturers tend to over-inflate HP ratings, assuming if the consumer see’s 6 HP advertised, rather than 2 HP, they are more apt to purchase the higher HP rated compressor. This is true in many situations. If you’re a muscle car enthusiast you would definitely consider the HP rating of a vehicle before buying it, right? But if we take a closer look at horsepower, as it relates to air compressors, we can seek out the truth.

HORSEPOWER
Horsepower was invented by an engineer by the name of James Watt. The same watt you think about when buying a light bulb. Watt is used as a measure of electrical and mechanical power. When we apply watts to HP, one HP is equivalent to 746 watts. So if you buy an air compressor rated at 6 HP and it operates on 120 volts it is, in a sense, a false rating. Here is why. If you plug the compressor into a standard 15 amp, 120 volt circuit it would only produce about 2HP (120 volts X 15 amps = 1800 watts). This is slightly over a 2 horse power rating.

The higher 6 HP rating advertised is commonly referred to as peak HP, similar to a vehicles engine HP rating. The peak HP rating of a vehicle engine is only accurate at a higher RPM range (usually 5000 to 6,000 RPM’s), but rarely do you drive at 5,500 RPM’s. As for the air compressor it would require more amps, from a 240 volt circuit, to produce this peak HP rating.

CUBIC FEET PER MINUTE
The Cubic Feet per Minute (CFM) is an important rating when it comes to portable air compressors. CFM is basically a measurement of the rate a compressor can deliver a volume of air. CFM varies with atmospheric pressure. It also varies with the temperature and humidity of the air. Air compressor manufacturers calculate Standard Cubic Feet per Minute (SCFM) as CFM at sea level with 68 degrees F, at 36% relative humidity.

Note: CFM ratings can be skewed by the manufacturer too. Let me explain

POUNDS PER SQUARE INCH
Let’s talk about our third rating, Pounds per Square Inch (PSI). For air compressors the CFM ratings are given at a specific PSI. In other words an air compressor rated at 3 CFM @ 90 PSI should be capable of delivering the 3 CFM at 90 PSI. The problem is air compressor manufacturers can advertise a higher CFM at a specific pressure because the air compressor is capable of delivering the rated CFM going from 0 to 90 PSI, but what is the true CFM delivered at 90 PSI. If your air tools or RV tires require a specific CFM rating at 90 PSI you more than likely won’t get it based on the advertised CFM @ a specific pressure. What this translates too is that it will take a long time to inflate some larger RV tires, if the compressor is in fact capable of inflating the tires at all.

When shopping for a portable air compressor the key is to try and find one that can deliver about 4 REAL CFM based on the REAL HP rating at 90 to 100 PSI.

If you have the storage room available, and you will have access to electricity, you can find some reliable pancake style portable compressors that will do a good job inflating tires and performing other small household jobs.

Tuesday, July 12, 2011

RV Garage Episode 12. Finishing up the roof of the trailer installation

In this episode of Mark's RV Garage, Mark finishes up the roof of the old Yellowstone trailer he's restoring.

Wednesday, June 29, 2011

Will adjusting "fins" on RV fridge fix a problem?

Dear Mark,
We went camping over the weekend and since then I have kept the fridge plugged in. While we were there camping and since returning everything in the fridge is frozen solid. I have adjusted the plastic clip that goes over the fins but it doesn't seem to do anything for adjusting the temperature. The cost to replace the fridge looks like a big ouch!! Any suggestions??!! Please and thank you.

Mark responds:
You didn't mention a make or model for the refrigerator, but there are a couple things that you can try. You mentioned adjusting the thermistor on the fins of the refrigerator. When you make an adjustment by sliding it up or down on the fins you need to allow the refrigerator to return to room temperature and then cool it down again to see if there is a change in the temperature. I recommend using a thermometer in the refrigerator compartment to get accurate readings when you make adjustments. Try moving it down on the fins for less cooling.

If the thermistor is properly attached to the fins, the wires have a good connection, and there is no change after making adjustments there is a good possibility that it went bad and will need to be replaced. On newer refrigerator models when a thermistor fails the refrigerator goes into a constant cooling mode, freezing everything in the refrigerator compartment. Thermistors aren't very expensive and most are fairly easy to replace, but you will need to adjust the new one as well.

Thursday, May 26, 2011

Why batteries die young and how you can help them live longer

The topic of RV batteries seems to come up a lot among RVers, and there is good reason for it. Did you know the average life for RV batteries with limited battery care and maintenance is only 2 to 3 years, and that 85% of all 12-volt batteries manufactured die before they should? That can get expensive, replacing two or more deep cycle batteries at a time.

Some of the reasons for these battery problems are undercharging, overcharging, not recharging a discharged battery in a timely manner, lack of maintenance, and a lack of understanding what is required to properly maintain batteries.

The #1 cause of battery failure is a condition called sulfation. When a battery is improperly charged, overcharged or undercharged, or allowed to self discharge small crystals of sulfuric acid from the battery’s electrolyte start to form on the charge plates. Over time this sulfate material cannot be converted back into active plate material and the battery is ruined.

This also occurs when a battery remains discharged for an extended period of time. These crystals act as a barrier, stopping the battery from ever accepting a full charge again regardless of how long you charge the battery. Once this happens, the power and longevity of the battery is severely reduced and your battery becomes one of the 85% that die before it should. Sulfation begins when a battery’s state of charge drops below 80%, or 12.4 volts.

I mentioned a moment ago that overcharging was one reason for batteries dying early. This is a common problem with RVs. The RV converter has a built in battery charger and most owners are under the impression that if you leave the RV plugged in when it is being stored it will keep the batteries topped off. Keeping the batteries topped off is extremely important, but the problem is many RV converter chargers provide a constant charge of about 13.5 volts which is too high for fully charged batteries. When this happens the electrolyte is boiled off resulting in an early death for the batteries.

ANOTHER PROBLEM IS NOT CHARGING the batteries at all when the RV is in short or long term storage or not recharging a discharged battery in a timely manner and letting it sit in that condition for extended periods of time. Both of these problems result in early battery death too.

Even for someone with a decent understanding of batteries and battery maintenance I had a few batteries that became statistics in the past. Then I discovered a way to prevent all of these battery related problems for good. It was a product that charges, maintains and conditions the batteries.

There are a few of these products on the market. The one I use is called The Battery Minder. What I mean by conditioning the battery is that the manufacturer of The Battery Minder has developed a simple but extremely effective circuitry that can safely dissolve the sulfation on the plates and restore much, if not all of the lost power. The reason The Battery Minder works so well is because it not only charges the battery, it maintains and desulfates the battery and will never overcharge the battery.

I’m not saying that you will never have to check the water levels or routinely inspect your batteries again, but this product will simplify your battery maintenance and extend the life of your batteries. It can even reverse sulfation on batteries that are already affected by this condition, if caught in time. It’s not very often that I endorse a product but The Battery Minder is one that I have been using for many years now, and through using it I have seen proven results.

When I’m not using the RV I hook the battery minder up and let it go. Through proper charging and maintenance you can easily double the life expectancy of your RV batteries.

If you would like to learn more about your deep cycle batteries check out our Deep Cycle Batteries DVD.

Wednesday, January 12, 2011

What is an RV tow dolly?

A tow dolly is a two wheeled trailer used to transport the vehicle you are towing with the drive wheels off of the ground. Tow dollies are a good choice when the vehicle you are towing cannot be towed with all four wheels down or if the vehicle would require expensive modifications to tow with all four wheels down.

Selecting the Right Tow Dolly
Tow dollies are manufactured to accommodate a certain size vehicle. They must be able to handle the width and the weight of the towed vehicle. Like everything else tow dollies have maximum weight ratings too. When you purchase a tow dolly make sure that it is designed to support the weight and size of the towed vehicle. Some dollies are adjustable, meaning the same dolly can be set-up to tow different size vehicles, and others are made to tow just one size vehicle. Normally the width of the towed vehicle determines the size tow dolly. Check with the tow dolly manufacturer before making a purchase.

Note: Matching the wrong vehicle and tow dolly can result in damage to the towed vehicle.

Some tow dollies come equipped with brakes and others do not. Check with State or Province laws and the motor home chassis manufacturer about the requirement for a towed vehicle braking system based on the amount of weight you will be towing before you purchase a tow dolly.

Loading and Unloading the Tow Dolly
Before loading the vehicle unto the tow dolly make sure the tow dolly coupler is properly attached to the ball mount and that you are using the proper size hitch ball for the coupler. Use a safety pin or clip to secure the locked coupler. Attach the safety chains or cables making sure they are crossed, “X” to form a saddle that would prevent the coupler from contacting the road surface in the event of a separation. Plug the light cable in and check all of the lights for proper operation. Follow the tow dolly manufacturer instructions to determine the proper hitch ball height.

Note: Because tow dolly manufacturers have different operating instructions it is essential that you follow the tow dolly manufacturer’s specific instructions for proper loading, unloading, and vehicle tie down procedures.

Tow Dolly Pre-Trip Checklist
Perform these checks before each travel day.

* Check and adjust tire pressure to manufacturer recommendations. Check when tires are cold before traveling more than one mile.

* Check wheel lug nuts. Tighten to manufacturer specifications.

* Check that wheel hubs and bearings are properly adjusted and lubricated. Follow manufacturer instructions or have them checked by a repair facility.

* Check that all nuts and bolts are properly tightened. Do not use the dolly with any loose or damaged hardware.

* Check that the coupler is properly secured to the ball mount. Note: Follow manufacturer instructions for adjusting coupler tightness.

* Check the safety chains for proper attachment.

* Check all lights for proper operation.

* Check that the tow vehicle is properly secured to the tow dolly. Note: Follow manufacturer instructions.

* Make sure the towed vehicle parking brake is released after it is properly secured to the dolly.

* Stop after 10 miles of travel to check the tie down straps. Readjust as required. Check every 100 miles afterwards as a minimum.

* Do not attempt to back the tow dolly when vehicle is loaded on it!

Some Tow Dolly Towing Tips
* Perform all pre-trip checks before using the tow dolly.

* Make turns wider than you are accustomed to. Do not attempt to make sharp turns or U-turns. If you turn to sharply the vehicle you are towing can come in contact with the tow dolly fender causing damage to both the towed vehicle and dolly.

* Do not attempt to back the loaded tow dolly. Backing can damage the tow dolly and the towed vehicle.

* Allow a safe following distance, and anticipate all stops in advance.

* Do not speed, drive at a safe speed and keep in mind the dolly is wider than some vehicles towing it. Stay centered in your lane of traffic.

* If you experience excessive sway it may be caused by an improperly loaded tow dolly. Stop when it is safe, check and retighten the tie downs, or reload the vehicle. Check tie down straps every 100 miles at a minimum.

* The towed vehicle should always be facing forward on the dolly. A towed vehicle loaded from the rear can contribute to trailer sway.

* Never allow any passengers to ride in the towed vehicle.

Learn about Mark Polks extensive of helpful DVDs, books and eBooks at RVbookstore.com

Wednesday, December 22, 2010

When hooked up, do I still need batteries in my RV?

Dear Mark,
For most RVs (I have a travel trailer) is the battery necessary to operate 12V appliances and accessories when you are plugged into shore power? In other words, does the AC current flow through the converter (converted to DC current) and then to the battery? or does the AC current flow through the converter and then directly to the 12V appliance and/or accessory?

For my trailer, if I'm plugged into shore power and I do not have the battery connected, only those appliances and accessories that operate on 120V will work (eg, air conditioner, microwave, etc). It would appear, therefore, that the battery is necessary even though I have shore power. (this was a surprise to me before I studied the AC / DC systems in a RV -- I initially thought that when plugged into shore power, my battery was not being used and all power consumption was coming directly from the AC current (converted to DC via the converter). I'm just trying to confirm that it's normal for only the 120V appliances/accessories to operate when (1) plugged into shore power and (2) battery is not connected.

Mark Says:
If the converter is operating properly you should not need the battery when it is plugged into electricity. The problem with not having a battery on the TT is the break-away system won't work when towing the RV. If you have no 12 volt devices operating (lights, fans, radio etc) when you are plugged into electricity (without a battery) something is probably wrong with the converter.