With prime travel and camping season upon us I thought I would offer some RV driving and towing tips. Some of these tips apply to pulling a trailer, some apply to driving a motorhome and some apply to both.
*Don't speed. Driving at a moderate speed will put less stress and strain on the drive train components of your tow vehicle. It will also reduce the likelihood of the trailer becoming unstable and starting to sway.
*Monitor the gauges on the tow vehicle or motorhome instrument panel. If a gauge does not read in the normal range pull over as soon as it is safe, and call for assistance.
*Drive defensively! Stay alert and monitor what is going on around you at all times. Use your mirrors. For increased visibility, purchase some convex mirrors that you can apply on your side view mirrors. These mirrors are inexpensive and are available in auto parts stores. They come in different sizes and improve your visibility a great deal, especially along the sides of the RV and in blind spots.
*If you're pulling a trailer it may be necessary to add mirror extensions so you can see along the sides of the trailer. The mirrors on your tow vehicle can be your best friend when you're towing a trailer. When you use your mirrors you will know when a transfer truck is passing and you can anticipate the need for a slight steering correction when the trucks air pressure causes the trailer to move.
*Use the proper gear for driving conditions. If the transmission continues to shift in and out of overdrive you need to turn the overdrive off. Reducing gears can help to slow the trailer or motorhome down when descending inclines and give you the additional power you may need when ascending inclines.
Note: Read the tow vehicle owner’s manual for proper gear selection when towing.
*Try to avoid sudden stops. Stopping too quickly can cause a trailer to slide and possibly jackknife.
*Try to avoid quick, harsh steering movements if possible. This can cause a trailer to become unstable and increase the possibility of trailer sway.
*Slow down on loose road surfaces, such as gravel, and when the roads are slippery and wet.
*When towing a trailer or a vehicle behind a motorhome you need to make wider turns than you are accustomed to. Remember the pivot point for the trailer is its axles. Watch for tail swing and exercise caution when turning on narrow streets and maneuvering around fuel stations.
*When maneuvering around the campground, watch for tail swing, low branches and utility hook ups.
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Tuesday, June 5, 2012
Tuesday, May 22, 2012
Trailer Towing Tips & Hints
I received an email from a reader who was involved in a bad accident while towing a trailer. The accident was a result of a sudden wind shear, causing the trailer to start swaying out of control. The truck and trailer rolled over. Fortunately everybody was okay!
After detailing the accident, Mary who was driving at the time, asked me if I had any tips or hints to offer on trailer brakes, controlling sway, and what to do when you experience something like wind shear, cross winds, or towing in windy conditions. After reading Mary’s email I thought it would be an appropriate topic for an article.
Let me begin by saying that the safest measure for traveling by any RV in windy conditions is not to travel at all. RV’s have a great deal of mass (length, width & height) and when that mass is confronted with strong wind gusts, crosswinds and/or wind shear the results can be devastating.
Sometimes the weather forecast can warn us that windy conditions are expected. These are the days that you need to make a conscious decision to stay put at the campground, or wherever you might be, and not take a chance traveling by RV. Trust me when I say it’s not worth the risk involved.
On the other hand what do you do when you are traveling on a fairly calm day and suddenly you are hit by a strong wind gust or crosswind? If you've been traveling by RV for awhile, either motorized or towable, you have probably experienced the forces of wind against the RV at one time or another. Possibly the most common occurrence is when a transfer truck passes you from the rear. I refer to this as the push, pull effect. The force of the air pressure coming off of the truck as it begins to pass pushes against the side of the RV and as the truck completes the passing maneuver it pulls you back in again. If you are not aware of a truck getting ready to pass you, or if you are towing a trailer and don't have some type of sway control this air pressure can cause the trailer to start swaying. The same dynamic occurs when a sudden wind gust hits the side of the RV unexpectedly.
The forces of air pressure are not the only thing that will cause a trailer to sway. Sway becomes an automatic factor with travel trailers simply because of how the trailer is hitched to the tow vehicle. The good news is that even though the potential for trailer sway is there, it can be controlled.
Handling Trailer Sway
Most of these causes for trailer sway have quick and easy fixes. For starters, before you purchase a travel trailer do your homework on the trailer. A poorly designed trailer will never handle well. Find a trailer with a tongue weight that is 10 to 15 percent of the trailers weight and match it with a tow vehicle that is capable of handling the load.
It is safe to say that with a well designed trailer, the proper tow vehicle, correct tire pressure, correct hitch adjustments, sway control and a properly loaded trailer we can control a great deal of potential trailer sway. That narrows the potential for sway down to what you could encounter at any given moment, even with a stable trailer; strong crosswinds, transfer trucks passing from the rear, bad driving conditions and descending steep inclines. Any one of these conditions will tend to push the trailer and tow vehicle sideways, but when equipped with the proper type of sway control and brakes, you can make normal steering corrections.
If the trailer become unstable and attempted steering corrections don't control it you can use the manual override on the electronic brake control to regain control of the trailer. Slide the manual lever over slowly and allow the trailer brakes to engage and the sway control to bring the trailer back on a straight course. If trailer sway becomes severe, reduce your speed gradually, avoid using the vehicle brakes if possible and manually apply more trailer brakes.
The brakes on the tow vehicle and trailer are a critical element to safe towing. Electric brake controllers are an essential component to safe trailer towing. The brake controller is installed inside the tow vehicle and supplies the power from the tow vehicle to the trailer’s electric brakes. There are two types of electric brake controllers, time delay activated and inertia activated. Time delay or solid-state controllers apply gradual voltage to the trailer brakes using a time delay circuit. A pendulum circuit that applies gradual voltage to the trailer’s brakes activates inertia or pendulum type controllers.
Both types of brake controllers allow you to adjust the amount of braking power, and they both have manual overrides that can be used to activate the trailer brakes without using the vehicle brakes. The override feature can be used when descending an incline to assist in slowing down and to prevent premature brake wear on the tow vehicle. It is also helpful in regaining control if the trailer begins to sway or fishtail. Always check the operation of the brake controller and trailer brakes before leaving on a trip.
Trailer Towing Tips
*Have your trailer brakes, bearings and other components inspected at least once annually by a professional.
*Allow more distance for stopping then you are accustomed to. Do not follow other vehicles too closely.
*Do not use the tow vehicles brakes to control excessive trailer sway. This will usually make it worse. Manually apply the trailer brakes to regain control.
*When descending a steep incline, if it feels like the trailer is pushing the tow vehicle, reduce speed, down shift to a lower gear and use the manual override on the brake control to slow the trailer. Heavy use of the tow vehicle brakes can cause them to overheat and begin to fade.
*Always be prepared to slow down and try to avoid making sudden stops.
Passing Vehicles
*Allow more time for acceleration when planning to pass somebody. It may be necessary to shift out of overdrive for increased acceleration.
*Only attempt to pass a vehicle on a level road surface. Never attempt passing on steep upgrades or downgrades.
*When passing a vehicle or changing lanes, signal in advance and double check mirrors for oncoming traffic.
*When completing a pass, look in your mirror, if you can see both of the vehicles front tires on the road surface behind the trailer it is safe to signal and begin pulling back into that lane.
*When passing, or being passed, anticipate the need to make steering corrections due to the air pressure created by other vehicles.
*Always be cautious of the road shoulder when passing vehicles. If the trailer gets on the shoulder it can jackknife or cause you to lose control.
Upgrades and Downgrades
Some vehicles have transmission tow modes. Consult your owner’s manual for the proper gears to use on your tow vehicle when towing a trailer.
*Downshift on downgrades to lessen the braking action required. Reduce your speed. Remember that trailer sway is more likely to occur when descending inclines.
*Downshift on upgrades for increased acceleration and power.
*On steep or long downgrades, reduce gears and avoid prolonged brake use on the tow vehicle. The brakes can easily overheat. Use the vehicle brakes in intervals.
*If the trailer becomes unstable when descending an incline and the trailer starts to sway, reduce your speed, avoid using the vehicle brakes, and manually activate the trailer brakes to regain control.
*On steep or long upgrades monitor all of the gauges on the tow vehicle instrument panel. If gauges do not read in the normal range, or the vehicle starts to overheat, pull over as soon as you safely can and call for help.
Let me begin by saying that the safest measure for traveling by any RV in windy conditions is not to travel at all. RV’s have a great deal of mass (length, width & height) and when that mass is confronted with strong wind gusts, crosswinds and/or wind shear the results can be devastating.
Sometimes the weather forecast can warn us that windy conditions are expected. These are the days that you need to make a conscious decision to stay put at the campground, or wherever you might be, and not take a chance traveling by RV. Trust me when I say it’s not worth the risk involved.
On the other hand what do you do when you are traveling on a fairly calm day and suddenly you are hit by a strong wind gust or crosswind? If you've been traveling by RV for awhile, either motorized or towable, you have probably experienced the forces of wind against the RV at one time or another. Possibly the most common occurrence is when a transfer truck passes you from the rear. I refer to this as the push, pull effect. The force of the air pressure coming off of the truck as it begins to pass pushes against the side of the RV and as the truck completes the passing maneuver it pulls you back in again. If you are not aware of a truck getting ready to pass you, or if you are towing a trailer and don't have some type of sway control this air pressure can cause the trailer to start swaying. The same dynamic occurs when a sudden wind gust hits the side of the RV unexpectedly.
The forces of air pressure are not the only thing that will cause a trailer to sway. Sway becomes an automatic factor with travel trailers simply because of how the trailer is hitched to the tow vehicle. The good news is that even though the potential for trailer sway is there, it can be controlled.
Handling Trailer Sway
Most of these causes for trailer sway have quick and easy fixes. For starters, before you purchase a travel trailer do your homework on the trailer. A poorly designed trailer will never handle well. Find a trailer with a tongue weight that is 10 to 15 percent of the trailers weight and match it with a tow vehicle that is capable of handling the load.
It is safe to say that with a well designed trailer, the proper tow vehicle, correct tire pressure, correct hitch adjustments, sway control and a properly loaded trailer we can control a great deal of potential trailer sway. That narrows the potential for sway down to what you could encounter at any given moment, even with a stable trailer; strong crosswinds, transfer trucks passing from the rear, bad driving conditions and descending steep inclines. Any one of these conditions will tend to push the trailer and tow vehicle sideways, but when equipped with the proper type of sway control and brakes, you can make normal steering corrections.
If the trailer become unstable and attempted steering corrections don't control it you can use the manual override on the electronic brake control to regain control of the trailer. Slide the manual lever over slowly and allow the trailer brakes to engage and the sway control to bring the trailer back on a straight course. If trailer sway becomes severe, reduce your speed gradually, avoid using the vehicle brakes if possible and manually apply more trailer brakes.
The brakes on the tow vehicle and trailer are a critical element to safe towing. Electric brake controllers are an essential component to safe trailer towing. The brake controller is installed inside the tow vehicle and supplies the power from the tow vehicle to the trailer’s electric brakes. There are two types of electric brake controllers, time delay activated and inertia activated. Time delay or solid-state controllers apply gradual voltage to the trailer brakes using a time delay circuit. A pendulum circuit that applies gradual voltage to the trailer’s brakes activates inertia or pendulum type controllers.
Both types of brake controllers allow you to adjust the amount of braking power, and they both have manual overrides that can be used to activate the trailer brakes without using the vehicle brakes. The override feature can be used when descending an incline to assist in slowing down and to prevent premature brake wear on the tow vehicle. It is also helpful in regaining control if the trailer begins to sway or fishtail. Always check the operation of the brake controller and trailer brakes before leaving on a trip.
Trailer Towing Tips
*Have your trailer brakes, bearings and other components inspected at least once annually by a professional.
*Allow more distance for stopping then you are accustomed to. Do not follow other vehicles too closely.
*Do not use the tow vehicles brakes to control excessive trailer sway. This will usually make it worse. Manually apply the trailer brakes to regain control.
*When descending a steep incline, if it feels like the trailer is pushing the tow vehicle, reduce speed, down shift to a lower gear and use the manual override on the brake control to slow the trailer. Heavy use of the tow vehicle brakes can cause them to overheat and begin to fade.
*Always be prepared to slow down and try to avoid making sudden stops.
Passing Vehicles
*Allow more time for acceleration when planning to pass somebody. It may be necessary to shift out of overdrive for increased acceleration.
*Only attempt to pass a vehicle on a level road surface. Never attempt passing on steep upgrades or downgrades.
*When passing a vehicle or changing lanes, signal in advance and double check mirrors for oncoming traffic.
*When completing a pass, look in your mirror, if you can see both of the vehicles front tires on the road surface behind the trailer it is safe to signal and begin pulling back into that lane.
*When passing, or being passed, anticipate the need to make steering corrections due to the air pressure created by other vehicles.
*Always be cautious of the road shoulder when passing vehicles. If the trailer gets on the shoulder it can jackknife or cause you to lose control.
Upgrades and Downgrades
Some vehicles have transmission tow modes. Consult your owner’s manual for the proper gears to use on your tow vehicle when towing a trailer.
*Downshift on downgrades to lessen the braking action required. Reduce your speed. Remember that trailer sway is more likely to occur when descending inclines.
*Downshift on upgrades for increased acceleration and power.
*On steep or long downgrades, reduce gears and avoid prolonged brake use on the tow vehicle. The brakes can easily overheat. Use the vehicle brakes in intervals.
*If the trailer becomes unstable when descending an incline and the trailer starts to sway, reduce your speed, avoid using the vehicle brakes, and manually activate the trailer brakes to regain control.
*On steep or long upgrades monitor all of the gauges on the tow vehicle instrument panel. If gauges do not read in the normal range, or the vehicle starts to overheat, pull over as soon as you safely can and call for help.
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Tuesday, May 15, 2012
Who is driving that motorhome?
Last summer we took our motorhome on a 6,000 mile roundtrip vacation.
It seems like more often than not we are on a tight schedule, forcing us to put in more miles per day than we'd like. I wanted this trip to be more leisurely as it pertained to how many hours I was behind the wheel each day.
Admittedly I am one of those people who likes to do all of the driving myself and my wife Dawn is happy with our arrangement. I know Dawn is a competent driver (she even has her CDL) but I still prefer to do the driving. I also think it is extremely important that both individuals are capable of driving or towing the RV. You never know when your travel partner will need to drive the RV and they should feel comfortable and confident in doing so.
As we were planning that summer trip, it brought back a memory of a past trip we took in the RV. We were stopped in traffic because of an accident, and were stuck in the same spot without moving for at least 30 minutes. I told Dawn that I was going to run back and use the bathroom and if traffic started moving to just get behind the wheel and drive. The boys were in the back bedroom playing X Box.
The motorhome started moving about the same time that I came out of the bathroom. Both boys looked up at me with their eyes wide open and my older son (Dawn's step-son) said, "If you're back here with us who's driving the motorhome?" My youngest son (also Dawn's stepson), who was about eight at the time, leaped up and ran to the front of the motorhome and said, "Dawn just pull over as soon as you can and let Dad drive."
The boys never saw Dawn drive the motorhome and just assumed she couldn't or shouldn't be driving it. At that point I made a mental note to myself to one day produce a driving DVD to help teach people who don't drive the RV how to do it. It took a while but eventually we produced these helpful DVDs:
Drive your Motorhome Like a Pro DVD
Trailer Towing, Weights, Hitch Work & Backing DVD
Tow Your 5th Wheel Trailer Like a Pro DVD
Watch my video below that shows how to establish your reference points for safe motorhome driving operation:
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
It seems like more often than not we are on a tight schedule, forcing us to put in more miles per day than we'd like. I wanted this trip to be more leisurely as it pertained to how many hours I was behind the wheel each day.
Admittedly I am one of those people who likes to do all of the driving myself and my wife Dawn is happy with our arrangement. I know Dawn is a competent driver (she even has her CDL) but I still prefer to do the driving. I also think it is extremely important that both individuals are capable of driving or towing the RV. You never know when your travel partner will need to drive the RV and they should feel comfortable and confident in doing so.
As we were planning that summer trip, it brought back a memory of a past trip we took in the RV. We were stopped in traffic because of an accident, and were stuck in the same spot without moving for at least 30 minutes. I told Dawn that I was going to run back and use the bathroom and if traffic started moving to just get behind the wheel and drive. The boys were in the back bedroom playing X Box.
The motorhome started moving about the same time that I came out of the bathroom. Both boys looked up at me with their eyes wide open and my older son (Dawn's step-son) said, "If you're back here with us who's driving the motorhome?" My youngest son (also Dawn's stepson), who was about eight at the time, leaped up and ran to the front of the motorhome and said, "Dawn just pull over as soon as you can and let Dad drive."
The boys never saw Dawn drive the motorhome and just assumed she couldn't or shouldn't be driving it. At that point I made a mental note to myself to one day produce a driving DVD to help teach people who don't drive the RV how to do it. It took a while but eventually we produced these helpful DVDs:
Drive your Motorhome Like a Pro DVD
Trailer Towing, Weights, Hitch Work & Backing DVD
Tow Your 5th Wheel Trailer Like a Pro DVD
Watch my video below that shows how to establish your reference points for safe motorhome driving operation:
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Tuesday, May 8, 2012
How To Install an RV Window Awning
In the past I have received several e-mails from fellow RVers asking if it's difficult to install a window awning on their RV. My reply was that this is one of those do-it-yourself things most RV owners can install and save some money at the same time.
Window awnings are a nice addition to your RV. They provide us with shade, keep rain away from the RV windows, and protect the interior fabrics and upholstery from damage caused by the sun. And the good news is they are really easy to install. You can save well over $100 in labor fees, and have the satisfaction of knowing you did it yourself. Watch the installation video for easy to follow directions.
Note: The instructions provided here are for installing an A&E Elite window awning.
When your window awning arrives unpack it and make sure all required parts are on hand. Let’s get started with the installation.
Step 1: Install the Awning Rail
Apply a caulking compound on the back of the awning rail before securing it. I use putty tape that you can purchase from an RV dealer. Position and center the awning rail approximately 5″ above the top of the window. Secure the awning rail with #6- x 1/2″ sheet metal screws provided
Step 2: Hang the Awning
Secure the awning arms to the top casting using the 1/4″ x 3/4″ bolts provided. Both arms are identical.
Now unroll just enough fabric so you can slide the bead into the awning rail. If too much fabric is unrolled before you release the preset tension, there will not be the required amount of tension needed to properly roll the awning back up after use.
Step 3: Install the Bottom Mounting Bracket
Position the bottom mounting bracket of each arm so the top of the end cap on each side of the tube is level with the opening of the awning rail. This insures the awning shield wraps up tightly. Mark the location of the bottom mounting bracket holes.
If the brackets will be secured to a wood structure, drill four 1/8″ diameter holes and secure the bottom brackets using four #10 screws. Apply caulking compound to screws before inserting. If the brackets are only secured to the skin of the RV, use a #5 drill bit, and secure the bottom mounting bracket using 3/16″ x 1″ Oscar Rivets. Apply caulking compound to rivets. Repeat on the other awning arm bracket.
Step 4: Release the Preset Tension
A & E window awning torsions are pre- wound at the factory. Remove the cotter pin that is holding factory pre-set tension. The cotter pin is in the roller tube end cap. Twist the roller tube as if unrolling the awning while pulling on cotter pin. Caution: When cotter pins are removed, springs are under tension. The awning will attempt to close. Keep your body and clothing clear of hardware and roller tube. Repeat on the other side. The awning should roll up snugly against the side of the vehicle.
Step 5: Installing the Window Strap Hanger
After the roller tube assembly is mounted on the RV, open the awning to its full extension by pulling down on the pull strap. Center the strap in the awning, then move the loop of the pull strap toward the RV and under the window to locate the placement of the window strap hanger.
Locate the strap hanger so that the top loop of the strap is engaged onto the hanger, allowing for minor height adjustment of the awning. Mark the location and install the strap hanger with three #10 x 3/4″ screws or 3/16″ x 1″ Oscar Rivets as required. Apply caulking compound to all screws or rivets before inserting.
Step 6: Center the window awning
For awnings with a metal weather shield, install #6 self-tapping screws into the awning rail immediately next to the metal hinge. Repeat this on other side. These screws hold the awning in place.
Your window awning installation is complete and ready to use. For more information on RV awnings check out our RV Awning Use, Care & Accessories DVD
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Thursday, May 3, 2012
Are You Braking the Law?
A topic that is sometimes overlooked, and seldom talked about is supplemental braking systems. It’s not about what supplemental braking system you have, it’s the fact that you have one!
One requirement for towing a trailer is that the trailer must have a braking system that works in conjunction with the tow vehicle brakes. Why should this requirement be any different for a motorhome towing a vehicle? In reality its not, but most people just assume you don’t need a supplemental braking system for the vehicle you’re towing. Some reasons for this assumption are:
1) Because of the size of the motorhome there is no need for a supplemental brake system on the tow vehicle.
2) People assume the vehicle they are towing is much lighter than it really is.
3) Braking laws are not always enforced by individual U.S. states and Canadian provinces.
4) Nobody took the time to educate the RV consumer on the requirement for a supplemental braking system.
Regardless of the type or model you choose, being able to stop completely, in less time and a shorter distance, will give you an added sense of safety whenever you’re towing a vehicle. And it’s the law in most cases. Most importantly, a supplemental braking system SAFELY reduces the stopping distance and helps to protect you, your loved ones and the safety of others.
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
One requirement for towing a trailer is that the trailer must have a braking system that works in conjunction with the tow vehicle brakes. Why should this requirement be any different for a motorhome towing a vehicle? In reality its not, but most people just assume you don’t need a supplemental braking system for the vehicle you’re towing. Some reasons for this assumption are:
1) Because of the size of the motorhome there is no need for a supplemental brake system on the tow vehicle.2) People assume the vehicle they are towing is much lighter than it really is.
3) Braking laws are not always enforced by individual U.S. states and Canadian provinces.
4) Nobody took the time to educate the RV consumer on the requirement for a supplemental braking system.
Regardless of the type or model you choose, being able to stop completely, in less time and a shorter distance, will give you an added sense of safety whenever you’re towing a vehicle. And it’s the law in most cases. Most importantly, a supplemental braking system SAFELY reduces the stopping distance and helps to protect you, your loved ones and the safety of others.
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Thursday, April 26, 2012
Post-Winter RV Checkup
Your house-on-wheels sat in storage for several months this winter and now it’s time for another camping season. What do you check to make sure the RV is safe and ready to use when you head out on your first RV trip of the season? There are lots of preventive maintenance checks you can perform, but here are the checks I consider essential.
1) Batteries: Start your post-winter checks with the batteries since it’s possible you removed them for winter storage. The condition of the batteries is dependent on how well they were cared for over the winter. Batteries in storage will lose a percentage of current through internal leakage. It’s not uncommon for a battery to discharge up to 10% a month when it is in storage. If you checked and recharged the batteries periodically while in storage they should be ready to go. If not, the first step is to fully charge the battery(s). Water should only be added to lead acid batteries after fully charging the battery, unless the water level is already below the plates. The plates need to be covered at all times. After the battery if fully charged check and add distilled water as required. If the batteries were removed for storage reinstall them making absolutely sure they are connected properly.
2) RV Water System (de-winterize/check for leaks/sanitize): Depending on how the unit was winterized it needs to be de-winterized. If you used non-toxic RV antifreeze to protect the water system you need to run fresh water through the entire system until all traces of the antifreeze are removed. Hopefully no antifreeze was added to the fresh water holding tank. If it was, the first step is to drain any remnants from the tank. Add potable water to the fresh water holding tank, turn the water pump on and open all of the water faucets. When clear water is running through the system turn the pump off and close the faucets. Take the water heater out of the by-pass mode (if applicable). If the water heater wasn’t bypassed the antifreeze needs to be drained from the water heater tank. Replace any water filter cartridges you removed for storage.
This is a good time t check the plumbing for leaks. With water in the fresh water holding tank turn the 12-volt water pump on and pressurize the water system until the pump shuts off. If the water pump cycles back on, even for a short period of time, there may be a leak somewhere. Try to locate the leak and repair it or take it to an authorized RV service facility to be repaired.
At this point I like to sanitize the water system (see video at the end of this post). Make sure all of the drains are closed and drain plugs are installed. Take a quarter-cup of household bleach for every fifteen gallons of water your fresh water tank holds. Mix the bleach with water into a one-gallon container and pour it in to the fresh water holding tank. Fill the fresh water holding tank completely full of water. Turn the water pump on and run water through all hot and cold faucets until you smell the bleach. Close the faucets and let it sit for twelve hours. Drain all of the water and re-fill the tank with potable water. Turn the water pump on and open all faucets, running the water until you no longer smell any bleach. It may be necessary to repeat this process to eliminate all signs of bleach.
3) Appliance Checks: Open the LP gas valve and check the operation of all LP gas fired appliances. Make sure the water heater tank is full of water before testing the water heater. If an LP gas appliance is not operating properly have it inspected by an authorized RV service facility. Insects are attracted to the odorant added to LP gas and nests can affect the appliance from operating properly.
Note: The LP gas system should have a leak test and gas operating pressure test preformed annually. These tests should be performed by an authorized RV repair facility.
Plug the unit into a reliable source of electricity and test 120-volt appliances and accessories for proper operation. Note: Make sure you have an adequate electrical source (30-50 amps) depending on your unit, before testing items like the microwave and roof air conditioner(s). After checking the refrigerator in the LP gas mode turn it off and with the doors open allow sufficient time for it to return to room temperature before checking it in the electric mode.
4) Tire Check: Just like a battery looses a percentage of its charge in storage, tires lose a percentage of air pressure. Your tires can lose 2-3 psi a month while sitting in storage. Check the tire pressure with a quality tire inflation gauge and adjust the inflation pressure to the manufacturer’s recommendation based on the load. Remember failing to maintain correct tire pressure, based on the load, can result in fast tread wear, uneven wear, poor handling, and excessive heat build-up which can lead to tire failure. Tire manufacturers publish load and inflation tables that should be followed for proper inflation pressure.
5) RV or Tow Vehicle Engine: Check all fluid levels. Check the transmission, power steering, engine coolant, engine oil, windshield washer and brake fluid. Consult your vehicle owner’s manual for proper levels. If a fluid level is low try to determine why and correct the problem. Service the engine and engine fluid levels according to specified intervals found in the owner’s manual. Start the engine and check for proper readings on all gauges. Check the operation of all lights. Make sure the vehicle emissions / inspection sticker is up to date.
If you have a generator check the oil level in the generator. Service the generator according to specified intervals found in the owner’s manual. Inspect the generator exhaust system for any damage prior to starting. Never run a generator with a damaged exhaust system. If you didn’t run the generator during storage start and run it for about two hours with at least a half-rated load. Check your generator owner’s manual for load ratings. If you didn’t use a fuel stabilizer and the generator won’t start, or continues to surge after starting, have it checked out and repaired by an authorized service facility.
6) Sealants & Seams: If you didn’t inspect the seams and sealants for potential leaks prior to storage or if the RV was stored outdoors this is a good time to do it. I recommend inspecting and resealing seams and sealants at least twice a year and possibly more depending on conditions. Inspect all roof and body seams and around any openings cut into the RV for signs of cracking or damage. Reseal any seams or sealants that show signs of cracking or separation. It’s important you consult your RV owner’s manual, or RV dealer, for sealants compatible with different types of materials you are attempting to seal. If you don’t feel comfortable performing the inspections or repairing seams and sealants have the maintenance performed by an authorized service facility. Note: Be extremely careful working on the RV roof. A fall can cause serious injury or death.
7) RV Safety Checks: Re-install any dry-cell batteries or fuses that were removed for storage. If batteries were not removed from safety devices replace them with new batteries now. Test the operation of the carbon monoxide detector, LP gas leak detector and smoke alarm. Inspect all fire extinguishers to make sure they are fully charged. If you have dry powder fire extinguishers shake and tap on the bottom to release the powder from the bottom.
These are what I consider to be essential post-winter checks so your RV is ready to roll when you are. You can add to this list and tailor it to your specific needs. Be safe and have a great camping season.
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
1) Batteries: Start your post-winter checks with the batteries since it’s possible you removed them for winter storage. The condition of the batteries is dependent on how well they were cared for over the winter. Batteries in storage will lose a percentage of current through internal leakage. It’s not uncommon for a battery to discharge up to 10% a month when it is in storage. If you checked and recharged the batteries periodically while in storage they should be ready to go. If not, the first step is to fully charge the battery(s). Water should only be added to lead acid batteries after fully charging the battery, unless the water level is already below the plates. The plates need to be covered at all times. After the battery if fully charged check and add distilled water as required. If the batteries were removed for storage reinstall them making absolutely sure they are connected properly.
2) RV Water System (de-winterize/check for leaks/sanitize): Depending on how the unit was winterized it needs to be de-winterized. If you used non-toxic RV antifreeze to protect the water system you need to run fresh water through the entire system until all traces of the antifreeze are removed. Hopefully no antifreeze was added to the fresh water holding tank. If it was, the first step is to drain any remnants from the tank. Add potable water to the fresh water holding tank, turn the water pump on and open all of the water faucets. When clear water is running through the system turn the pump off and close the faucets. Take the water heater out of the by-pass mode (if applicable). If the water heater wasn’t bypassed the antifreeze needs to be drained from the water heater tank. Replace any water filter cartridges you removed for storage.
This is a good time t check the plumbing for leaks. With water in the fresh water holding tank turn the 12-volt water pump on and pressurize the water system until the pump shuts off. If the water pump cycles back on, even for a short period of time, there may be a leak somewhere. Try to locate the leak and repair it or take it to an authorized RV service facility to be repaired.
At this point I like to sanitize the water system (see video at the end of this post). Make sure all of the drains are closed and drain plugs are installed. Take a quarter-cup of household bleach for every fifteen gallons of water your fresh water tank holds. Mix the bleach with water into a one-gallon container and pour it in to the fresh water holding tank. Fill the fresh water holding tank completely full of water. Turn the water pump on and run water through all hot and cold faucets until you smell the bleach. Close the faucets and let it sit for twelve hours. Drain all of the water and re-fill the tank with potable water. Turn the water pump on and open all faucets, running the water until you no longer smell any bleach. It may be necessary to repeat this process to eliminate all signs of bleach.
3) Appliance Checks: Open the LP gas valve and check the operation of all LP gas fired appliances. Make sure the water heater tank is full of water before testing the water heater. If an LP gas appliance is not operating properly have it inspected by an authorized RV service facility. Insects are attracted to the odorant added to LP gas and nests can affect the appliance from operating properly.
Note: The LP gas system should have a leak test and gas operating pressure test preformed annually. These tests should be performed by an authorized RV repair facility.
Plug the unit into a reliable source of electricity and test 120-volt appliances and accessories for proper operation. Note: Make sure you have an adequate electrical source (30-50 amps) depending on your unit, before testing items like the microwave and roof air conditioner(s). After checking the refrigerator in the LP gas mode turn it off and with the doors open allow sufficient time for it to return to room temperature before checking it in the electric mode.
4) Tire Check: Just like a battery looses a percentage of its charge in storage, tires lose a percentage of air pressure. Your tires can lose 2-3 psi a month while sitting in storage. Check the tire pressure with a quality tire inflation gauge and adjust the inflation pressure to the manufacturer’s recommendation based on the load. Remember failing to maintain correct tire pressure, based on the load, can result in fast tread wear, uneven wear, poor handling, and excessive heat build-up which can lead to tire failure. Tire manufacturers publish load and inflation tables that should be followed for proper inflation pressure.
5) RV or Tow Vehicle Engine: Check all fluid levels. Check the transmission, power steering, engine coolant, engine oil, windshield washer and brake fluid. Consult your vehicle owner’s manual for proper levels. If a fluid level is low try to determine why and correct the problem. Service the engine and engine fluid levels according to specified intervals found in the owner’s manual. Start the engine and check for proper readings on all gauges. Check the operation of all lights. Make sure the vehicle emissions / inspection sticker is up to date.
If you have a generator check the oil level in the generator. Service the generator according to specified intervals found in the owner’s manual. Inspect the generator exhaust system for any damage prior to starting. Never run a generator with a damaged exhaust system. If you didn’t run the generator during storage start and run it for about two hours with at least a half-rated load. Check your generator owner’s manual for load ratings. If you didn’t use a fuel stabilizer and the generator won’t start, or continues to surge after starting, have it checked out and repaired by an authorized service facility.
6) Sealants & Seams: If you didn’t inspect the seams and sealants for potential leaks prior to storage or if the RV was stored outdoors this is a good time to do it. I recommend inspecting and resealing seams and sealants at least twice a year and possibly more depending on conditions. Inspect all roof and body seams and around any openings cut into the RV for signs of cracking or damage. Reseal any seams or sealants that show signs of cracking or separation. It’s important you consult your RV owner’s manual, or RV dealer, for sealants compatible with different types of materials you are attempting to seal. If you don’t feel comfortable performing the inspections or repairing seams and sealants have the maintenance performed by an authorized service facility. Note: Be extremely careful working on the RV roof. A fall can cause serious injury or death.
7) RV Safety Checks: Re-install any dry-cell batteries or fuses that were removed for storage. If batteries were not removed from safety devices replace them with new batteries now. Test the operation of the carbon monoxide detector, LP gas leak detector and smoke alarm. Inspect all fire extinguishers to make sure they are fully charged. If you have dry powder fire extinguishers shake and tap on the bottom to release the powder from the bottom.
These are what I consider to be essential post-winter checks so your RV is ready to roll when you are. You can add to this list and tailor it to your specific needs. Be safe and have a great camping season.
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Monday, April 16, 2012
RVing at Wal-mart - One Bad Apple Spoils the Barrel
I am sure you have heard the expression “one bad apple spoils the barrel” at one time or another. When we travel in our RV and just want a few hours rest we usually stop and stay at a Wal-Mart along the way. Whenever we do this there is an unwritten protocol we follow to ensure that staying in a Wal-Mart parking lot remains an option for RVers in the future.
1) Always ask for permission to stay.
2) Always ask where they would like you to park. Never block loading zones.
3) Do not put out the lawn chairs, awning & BBQ grill.
4) Do not stay for more than one evening.
5) Do not use leveing jacks in the parking lot. The weight of the RV can cause damage to the asphalt. (See photo above)
There are more common-sense rules that apply, but these are what I consider to be some of the more important points to follow. We also reciporcate by shopping at the Wal-Mart to re-supply and re-stock the RV with any essential items.
Many Wal-Mart stores around the country offer this overnight parking service to RV owners until somebody spoils it for everybody. It’s easy to quietly pull-in, park, spend the evening, clean up after yourself and leave in the morning.
Try not to be the bad apple when it comes to staying at a Wal-Mart in your RV!
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
1) Always ask for permission to stay.
2) Always ask where they would like you to park. Never block loading zones.
3) Do not put out the lawn chairs, awning & BBQ grill.
4) Do not stay for more than one evening.
5) Do not use leveing jacks in the parking lot. The weight of the RV can cause damage to the asphalt. (See photo above)
There are more common-sense rules that apply, but these are what I consider to be some of the more important points to follow. We also reciporcate by shopping at the Wal-Mart to re-supply and re-stock the RV with any essential items.
Many Wal-Mart stores around the country offer this overnight parking service to RV owners until somebody spoils it for everybody. It’s easy to quietly pull-in, park, spend the evening, clean up after yourself and leave in the morning.
Try not to be the bad apple when it comes to staying at a Wal-Mart in your RV!
Happy RV Learning!
Mark Polk
RV Education 101
Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved
Subscribe to:
Posts (Atom)






