Monday, February 11, 2013

RV Jargon

When you work in the RV Industry, and are exposed to RVs almost everyday, you take some things for granted. One of those things is RV terminology. When I hear these terms I just assume everybody understands them. Here are some common RV terms that you will help enhance your RV jargon.



Arctic Package – An RV that is equipped with additional options for cold weather camping. Some but not all of these options may include additional insulation value, heated holding tanks and dual pane windows.

 
Axle Ratio – The number of times the drive shaft must turn to rotate the axle one revolution. If you have a 3.73:1 axle ratio, the drive shaft turns 3.73 times for each full turn of the axle. The higher the numeric value of the axle is the better the vehicle will tow, but it will use more fuel too.

 
Basement Storage – Storage compartments or storage area located below the floor of the RV. You access the storage from outside. Some storage areas are referred to as pass-through storage, meaning it goes from one side of the RV to the other with no dividers, and can be accessed from either side.

 
Break-away Switch – A switch that is wired into the trailers brake system. It is attached from the trailer to the tow vehicle by a cable lanyard. In the event that the trailer and vehicle separate, the cable pulls a pin from the switch and the trailer brakes are activated. The switch must have a 12-volt source to operate.

 
Bumper Pull – A loose term used to describe towing a travel trailer or pop-up trailer, also referred to as a pull behind.

 
Deep Cycle Battery – Often referred to as the auxiliary battery or house battery, it is used to supply 12-volt DC power to the appliances and accessories in the RV. Unlike an automotive starting battery a deep cycle battery is designed to hold a charge longer and be discharged repeatedly. The RV battery is charged when the motorhome is running, or in the case of a trailer, when the tow vehicle is running, if a charge line was wired in the trailer plug. It is also charged when the RV is plugged into a 120-volt power source and by an onboard generator when it is running.

 
Demand Water Pump – The onboard water system that operates using a 12-volt demand pump. When you have potable water in your fresh water holding tank, and the pump is turned on, it pressurizes the onboard water system. When you open a faucet and the water pressure drops, the pump cycles on and off to maintain a constant pressure.

 
Dinghy – A term used for the vehicle you are towing behind a motorhome.

 
Dry Weight – Dry Weight (DW) or Unloaded Vehicle Weight (UVW) is the actual weight of the RV as built at the factory. The DW does not include passengers, cargo, fresh water, LP gas, fuel or aftermarket accessories.

 
DSI- Direct Spark Ignition (DSI) is a system used to ignite the burner on a propane appliance with the touch of a button. It is commonly used on RV refrigerators, furnaces and on some water heaters.

 
Dump Outlet - Where both holding tanks terminate into one main drain outlet. This is where you connect the RV sewer hose to dump or empty the gray and black water holding tanks.

 
Full Hook-Up – A full hook-up means you connect the RV to the campground electric, water and sewer facilities. In addition to this it may also include cable TV connections.

 
Genset – A short term for a generator set.

 
Heat Strip – An electric heating element in a roof mounted air conditioner. A heat strip will take the chill off, but is not designed to actually heat the RV.

 
Kilowatts – Power generators are rated in kilowatts. One kilowatt equals 1,000 watts.

 
OEM – Abbreviation for Original Equipment Manufacturer

 
Porpoising – A term used to describe the up and down movement of an RV when traveling.

 
Refer – A short term for your RV refrigerator.

 
LP Regulator – LP gas regulators control or regulate the LP gas flow through all appliances, and maintain the proper operating pressure in the LP gas system.

 
Sewer hose donut – A plastic or rubber ring used to get a good seal between the sewer hose and the campground sewer connection. Sewer hose donuts are required at many campgrounds.

 
Shore Power – Shore power is a term used for plugging the RV in to an external 120-volt power source such as at a campground.

 
Slider Hitch – A 5th wheel hitch used on short wheelbase pickup trucks. On short wheelbase trucks the front of the 5th wheel trailer can make contact with the cab of the truck when making a sharp turn. A slider hitch has two positions. One for normal driving conditions and one for maneuvering where turns are required.

 
Stick and Tin – An RV with wood framing and corrugated aluminum exterior.

 
Three Way Refrigerator – An RV refrigerator that operates on 12-volt DC, 120-volt AC and LP gas.

 
Tongue Weight –Tongue Weight or Hitch Weight is the amount of weight pressing down on the vehicle’s hitch ball from the coupler of the trailer when the trailer is fully loaded for travel. For trailers that weigh over 2,000 pounds TW should be 10 to 15 percent of the loaded trailer weight.

 
Tote Tank – A portable tank used to dump the contents of a holding tank into, and then transport it to a dump station to be emptied.

 
Water Pressure Regulator – A water pressure regulator is used to prevent too much water pressure from entering the RV and damaging the plumbing system. You attach the pressure regulator to the campground water supply and then attach one end of your drinking hose to the regulator and the other end to the city water inlet on the RV.

 
Wheelbase – The distance between the centerlines of the primary axles of a vehicle.

 
Wide Body – An RV that is wider than 8 feet. A wide body RV is usually 8 feet 6 inches wide.



This list is not all-inclusive, but as you learn new terms you will improve your RV jargon.

There are many other common RV terms. I only posted a handful and would be interested to hear some of your RV terms. Feel free to share below in the comment section.
Happy RV Learning

Mark Polk

RV Education 101

Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »

Are you interested in what goes into restoring a vintage travel trailer? Follow the epic 7 month-long fun educational and entertaining journey as Mark and Tyler demo a vintage trailer down to the frame and rebuild to its former glory in this 4-DVD Set: Vintage Trailer Restoration Even if you never plan to restore an RV, you will learn an incredible amount of information about how your RV works.

Copyright, Mark Polk owner RV Education 101 – all rights reserved



Sunday, February 3, 2013

Important Aspects to Generator Longevity


If a generator is properly maintained and cared for it is quite possible it will last longer than the RV itself. Here are a few things to keep in mind to maintain your generator:

Preventive Maintenance: The key to a long lasting generator set is periodic maintenance. When it comes to generator sets we are primarily concerned with two types of maintenance, preventive maintenance and routine maintenance. Both can add years of life to your generator set. Preventive maintenance is maintenance you perform on your generator before a problem exists. These checks are designed to prevent or identify potential problems that could lead to mechanical breakdown, malfunction, or failure of a component or system on your generator. Preventive maintenance consists of cleaning, inspecting, lubricating, adjusting and servicing your generator. Prior to starting your generator you should, at a minimum, inspect the generator set for any fuel or oil leaks, inspect the exhaust system for proper mounting and for leaks and check the oil level. Make sure the CO detector(s) are operating properly and that all appliances are turned off.

 Routine or Scheduled Maintenance: For generator sets scheduled maintenance is performed in intervals based on hours of operation. Scheduled maintenance is designed to keep your generator set in top operating condition and prevent untimely breakdowns and repairs. It is absolutely essential that you read your generator owner’s manual and warranty information in regards to who is responsible for what when it comes to routine and scheduled maintenance. Often times scheduled maintenance that is required and not performed can void your warranty, and shorten the life of your generator set. Monitor the generator hour meter and have the required maintenance performed at specified intervals. Most generator owner manuals have periodic maintenance schedules listed, and maintenance logs to record and keep track of all maintenance performed.

 Exercise your Generator: One important aspect to generator longevity ,often times overlooked, is putting the generator to work. What I mean by that is exercising the generator set on a regular basis. This exercise routine helps solve several generator related problems when it sits unused for periods of time. For starters fuel related problems can occur in as little as one month of sitting idle. In addition to clearing out any stale fuel this monthly exercise regime also lubricates all of the engine seals and helps to prevent carbon build-up. And when you exercise your generator it heats up the generator windings and eliminates moisture build-up. Exercising the generator not only contributes to a more reliable generator, but it extends the life of the engine as well. So, what exactly do I mean when I say exercise your generator? I mean you should start and run the generator with at least a 50% percent load, for at least two hours every month. It is extremely important that you run it with this minimum rated load. Generators are designed to run with a load placed on them. Check your generator owner’s manual for load ratings specific to your generator set. And remember, when exercising the generator it’s always better to let it run longer (2-hour) periods than it is for shorter periods of time.

Generator Operating Conditions: When using your generator you need to consider current weather conditions. Make sure the engine oil viscosity is correct for ambient temperatures. For carbureted gasoline generators make sure the altitude setting is adjusted properly. Always remember to re-adjust altitude settings when you return to lower altitudes. In dusty conditions it will be necessary to perform air cleaner maintenance and change the oil more frequently. Being aware of the operating conditions and performing the required maintenance accordingly will help extend the life of your generator set.

There are gasoline, diesel and LP gas generators. Regardless of the type you own following the recommended maintenance intervals and exercising, operating and storing procedures will add years of reliable service to the generator set. Follow all cautions and warnings found in your generator owner’s manual.

NOTE* Always keep in mind that when operating any generator there is the threat of Carbon Monoxide poisoning.


 
Happy RV Learning!
Mark Polk

RV Education 101

Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »


Are you interested in what goes into restoring a vintage travel trailer? Follow the epic 7 month-long fun educational and entertaining journey as Mark and Tyler demo a vintage trailer down to the frame and rebuild to its former glory in this 4-DVD Set: Vintage Trailer Restoration Even if you never plan to restore an RV, you will learn an incredible amount of information about how your RV works.


Copyright, Mark Polk owner RV Education 101 – all rights reserved

Wednesday, January 23, 2013

Too Much to Remember? Check it Out, Check it Off

There are lots of things to remember, and to maintain on an RV. Sometimes we tend to overlook the simplest maintenance requirements on our RV. As the old saying goes, 'you can't see the forest for the trees.' Let’s take a quick look into some common RV owner maintenance oversights.
 
It’s not uncommon for your RV to sit in storage for periods of time. If dry cell batteries aren't removed from devices like smoke detectors and carbon monoxide detectors the devices won't work when you need them too. By simply getting in a habit of checking the smoke, CO, and LP gas leak detectors prior to each trip you can prevent this from happening. Follow the testing instructions in the owner’s manual or on the device itself. If you remove dry cell batteries during storage remember to re-install them in the spring.


You also need to get in a habit of inspecting the fire extinguisher before each trip. Look to see if the arrow is pointing in the green area in the sight gauge. If it reads empty or needs charging replace it or have it recharged immediately. If it’s a dry powder type fire extinguisher the arrow pointing in the green doesn't always guarantee it will work. Every month you should turn dry powder extinguishers upside down, tap on the bottom of the extinguisher and shake it so the powder that settled on the bottom is released. Make sure you know how to operate the fire extinguisher too.

So, how do we go about remembering all this stuff every time we take a trip? By using a simple pre-trip checklist. A pre-trip checklist can serve as a reminder to check and test all safety devices prior to leaving on an RV trip.

Happy RV Learning!
Mark Polk

RV Education 101

Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »

Are you interested in what goes into restoring a vintage travel trailer? Follow the epic 7 month-long fun educational and entertaining journey as Mark and Tyler demo a vintage trailer down to the frame and rebuild to its former glory in this 4-DVD Set: Vintage Trailer Restoration Even if you never plan to restore an RV, you will learn an incredible amount of information about how your RV works.


Copyright, Mark Polk owner RV Education 101 – all rights reserved

Tuesday, January 8, 2013

Overloading your RV is Unsafe!

Weighing your RV can be the difference between a safe, enjoyable trip and a costly, disastrous trip. With multiple slide-out rooms, amenities like washers and dryers, large holding tank capacities and the ample amount of storage space available on today’s RVs it’s easy to see why so many are overloaded. Overloaded RVs are extremely dangerous.

Note: When talking about weights and weighing RVs there are some differences between motorized and towable RVs. This article is generic in nature and some terms and definitions for certain type RVs are excluded. My goal with this article is to discuss weight issues that commonly apply to both categories of RVs. There are more reasons for weighing your RV than I list here, but my intent is to highlight some of the most important reasons for weighing your RV.
First and foremost safety is the number one reason to weigh your RV. Driving or towing an overloaded RV is a leading cause for RV accidents. Overloading your RV puts you, your passengers and other people in harms way.

Overloading RVs is tough on the tires. The tires on your RV are the most vulnerable component affected by overloading. There are numerous reasons for this. One reason is if the tires are not inflated properly for the load. Failure to maintain correct tire pressure can result in fast tread wear, uneven wear, poor handling, and excessive heat buildup which can lead to tire failure. Another problem is, when you weigh your RV the total weight of the axles may be within the axle weight rating but it can still be overloaded on one side of the axle or the other.

For the sake of an example let’s say you have an axle that is rated for 6,000 pounds. When we weigh the RV the weight on that particular axle is 5,950 pounds. We are within the weight rating for the axle itself, but when we weigh each axle end separately we discover that one end weighs 3,400 pounds and the other end weighs 2550 pounds. We are still within the 6,000- pound axle weight rating, but the tires are only rated for 3,000 lbs. at a specified inflation pressure. This means the axle end that weighs 3,400 pounds is overloading the tire by 400 pounds, even if the inflation pressure is correct. Eventually the overloaded tire will fail.

Overloaded RV’s can result in suspension system and brake related problems. Overloading can lead to rapid vehicle suspension system wear, or component failure to include: springs, shock absorbers, brakes and tires. Overloading the RV increases the stopping distance and if serious overload conditions exist for extended time periods the brakes can fail completely.

There is a reason RVs have weight ratings. The suspension system, tires, wheels, brakes, axles, and the RV itself all have weight ratings. Weight ratings are established by the manufacturer, and are based on the weakest link in the chain. When you exceed a weight rating you are overloading one or more of the components on the RV and risk wearing the component out prematurely or complete failure of the component.

1) The Gross Vehicle Weight Rating (GVWR) is one of the most crucial safety factors for your RV. The GVWR is the maximum allowable weight of the vehicle when fully loaded for travel including: all passengers, all cargo, fluids and fuel. The GVWR is equal too or greater than the sum of the unloaded vehicle weight (UVW) plus the net carrying capacity (NCC) for the RV.

2) The Gross Axle Weight Rating (GAWR) is the maximum allowable weight that can be loaded on each axle of the RV. The GAWR is based on the lowest weight rating of other components in the system like suspension components, brakes, wheels, and tires.

3) The Gross Combined Weight Rating (GCWR) is the maximum allowable combined weight of the fully loaded vehicle and the fully loaded vehicle/trailer being towed. It is dangerous to exceed any weight rating, and the only way to know is to have the RV weighed.

Note: There are many other weight ratings for motorized and towable RV’s. Never exceed any weight rating.

Poor weight distribution is a common problem that contributes to overloads. When weight is not properly distributed and/or the RV is loaded improperly the tire(s) and other components on the end of the axle that is overloaded are subject to failure. When a tire fails many RVers contribute it to a defect in the tire, but with overload conditions that is seldom the case. The only way to avoid this is to weigh each axle end separately to determine if a tire overload condition exists. If any overload condition exists it must be resolved immediately. In some cases it might be possible to redistribute the weight and weigh it again. If the overload condition still exists you will need to remove some of the weight from the RV.

Overloading can result in untimely breakdowns and costly repairs. When an overload condition exists components on the RV can wear out prematurely. Transmissions overheat, brakes wear out, tires fail and the end result can be an unexpected and sometimes dangerous breakdown. These situations can often be avoided by knowing and managing the weights in and on your RV.

Overloading your RV is unsafe! That’s the bottom line.

That’s some pretty convincing reasons for weighing your RV, but just how do you go about it? The actual process of weighing your RV is not that difficult. It may take a little time at the scales, but it is well worth it knowing that you are traveling safely within all weight ratings.

The first step is to find scales where you can weigh your RV. This shouldn't be a problem; you can look in the Yellow Pages under moving and storage companies, gravel pits and commercial truck stops. There are several different types of scales. What is important is to find scales where you can weigh individual wheel positions in addition to the overall weight, and the axle weights. Remember I said earlier it is quite possible to weigh an axle and be within the Gross Axle Weight Rating, but you can exceed the tire rating on one axle end or the other. Call the number where the scales are located and ask them if it is possible to weigh your RV in these configurations.

The next step is to weigh everything! The day you head to the scales have the RV fully loaded for travel. If you tow a vehicle or trailer behind the motorhome take the loaded vehicle with you. If it’s a tow vehicle and trailer have it loaded as if you were leaving on a camping trip. Be sure to include all passengers, cargo, food, clothing, fuel, water, and propane.

I am including a link to a brochure that you can download, print and take with you to the scales. It will walk you through the proper procedures for weighing your RV. CLICK HERE

Always keep in mind that weights can and do change according to how you load and distribute the weight in your RV and on many other factors. You should get into the practice of weighing your RV periodically to stay within all weight ratings. Whenever an overload condition exists resolve the problem before using your RV.

Happy RV Learning!
Mark Polk

RV Education 101

Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »
Copyright by Mark Polk owner of RV Education 101 – all rights reserved

Friday, December 28, 2012

Do you have RV Emergency Escape Plan?

When we plan a trip in our RV we tend to think about all of the good aspects of the upcoming adventure. Where we are going, what we'll do when we get there, and all of the things we will see and experience along the way. What we don't really think about is what if something happens during the trip and everybody needs to exit the RV in a hurry. What if there is a fire? What if the entry door is blocked and you can’t get out. What’s the plan? Is there a plan?
 
I don't want to worry anybody. My intent is to bring awareness to the possibility that something like this could happen, so you can discuss it and be prepared in the event of an emergency. An RV emergency escape plan is just one of those things lots of folks don't think about.
For starters the National Fire Protection Association (NFPA) require RVs to have emergency escape windows. Make sure everyone traveling with you (who are old enough) knows where the emergency escape window is located and how to use it. It’s a good idea to practice using it so you are familiar with how to get out of the RV in case of an emergency. Consider elderly persons and small children. Can they exit the emergency window without assistance, and if not what is the plan.
Here are some more important considerations when formulating your RV escape plan:

* In the event of an emergency the mission is to get everybody out of the RV quickly and in an orderly fashion.

*You should have an emergency escape plan for the front of the RV and the rear of the RV.

* Time is your biggest enemy if there is a fire. An RV can fill with smoke in as little as one minute.

* Design an escape plan specific to the needs of the individuals in the RV.

* Sketch your plan on paper and indicate which windows and doors can be used to escape. Review the plan with everyone in the RV. Make sure each adult understands their duties when it comes to assisting others.

* Make sure everybody knows where the emergency escape window is located and how to use it.

* Make sure everybody knows how to use other windows and door latches in the RV, before there is an emergency.

* Practice your escape plan so everybody is familiar with how to get out of the RV in case of an emergency.

* If possible, designate a meeting place outside where everybody will meet immediately after exiting the RV so you can get accountability.

* When everybody is safely out of the RV call 911 for help.

* Never re-enter a burning RV!

Most importantly do not risk your personal safety, or the safety of others attempting to put a fire out. The first step is to get everybody out of the RV and away from the fire safely. Have somebody call 911 for help, and if you can't extinguish the fire within the first minute or so let the professionals handle it.

Happy RV Learning!
Mark Polk
RV Education 101

Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »


Copyright by Mark Polk owner of RV Education 101 – all rights reserved

Tuesday, December 18, 2012

What is a Park Model or Recreational Park Trailer?

Recreational Park Trailers or RPTs are designed to be used as temporary living quarters for recreation, camping, or seasonal use. In many cases these seasonal cottages are taken to a vacation spot, set-up and left there. This can be in an RV park, resort area, or a tranquil location in the mountains or on the coast, usually within a few hours drive from the owner’s residence.

RPTs come in various designs but are normally one of two types. There are 12-foot wide models that are normally 36 feet in length. This type has a peaked, shingled roof and siding similar to a house or cottage. 12-foot wide models need to be transported and set-up by professionals with the proper type of permits and equipment.

Another common type of RPT is slightly less than 8’ 6” in width and up to 39 feet in length. This type resembles a travel trailer and can be transported by the owner with a proper tow vehicle, but the set-up requires trained professionals. Park models have slide-outs to extend the living space inside when they are set-up. Recreational park trailers do not exceed 400 square feet when they are set-up.

 Recreational park trailers come equipped with full bathrooms, kitchens, living room, bedrooms, heat and air, and are usually fully furnished. Because they are designed to be stationary, for the most part, many RPTs have full size appliances similar to those found in your home, rather than RV type appliances. Prices can range from $20,000 to well over $60,000.

Happy RV Learning!
Mark Polk
RV Education 101

Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »


Copyright by Mark Polk owner of RV Education 101 – all rights reserved

Sunday, December 9, 2012

A Logical Step to Selling your RV

The current economic situation has affected individuals, companies and industries alike. One industry hit especially hard was the RV industry. During a recession one of the first things to go among consumers is discretionary spending on big ticket items like RVs. This decrease in spending results in RV dealerships and RV manufacturers scaling back operations to keep the doors open until the economy rebounds.

The same holds true for many consumers who already own RV’s. They need to scale back and tighten their budget until the economy rebounds. In many cases consumers directly affected by the economic downturn are forced to sell their RV, to lower sthe amount of money going out of the household budget.

Selling a big ticket item like an RV can be a challenge in itself, especially when the seller doesn’t have a thorough understanding of how the entire selling process works. If you still owe money on the RV there is a lien holder, there are numerous Department of Motor Vehicle (DMV) rules and regulations to follow and chances are financing will need to be arranged. Other considerations include how to market and advertise the RV and how much is the RV is actually worth?

Sometimes things are best left to the pros, and this is one of those times. A logical step to selling your RV is to discuss putting it on consignment at your local RV dealership. Selling an RV on consignment means the RV dealership will attempt to sell your RV the same as they would their own used RV inventory for an amount you both agree on. They advertise your unit, show it to potential customers, help arrange the financing and take care of all the required paperwork after the sale. So it only seems logical that the best way to sell your RV is where other people go to buy an RV.

But as the old saying goes, if something sounds too good to be true it probably is. As good as it may sound when yo sell your RV on consignment there are many things you need to be aware of. When I was a sales manager for an RV dealership we sold lots of RVs on consignment. I witnessed just about every mistake owners could make, from leaving personal items in the RV unsecured to dropping their RV insurance in an attempt to save some money during the time it was being sold. I mentioned earlier that one of the reasons for selling the RV in the first place is to cut back on some of the money going out of the household budget. But, whether you try selling the RV on your own, or on a consignment lot, you are still responsible for the monthly RV payment and for keeping the RV insured until it sells. The RV dealer will specify in the consignment contract that they are not liable for any damage to the RV while it is in their possession, and that you are required to keep the unit insured. This not only protects you while the RV is sitting on the dealer’s lot, but you are required by law to have insurance on the RV if it is financed.

It is important that you sit down with the dealership and go over the entire consignment agreement before you sign any paperwork. You need to understand how much the dealership will get paid, what selling price you agree on, what the term of the agreement is, what you are responsible for and what the dealership is responsible for. It may be that you owe more on the RV than it is actually worth. When you factor this in with the percentage the dealerhip gets paid the RV could potentially sit on the lot month after month and never sell. In a situation like this you will need to agree on a reasonable selling price and it may be necessary for you to pay the balance of the loan when the RV sells. Remember the goal is to sell the RV!

You will be responsible for preparing the RV for sale. This includes things like cleaning the RV, draining the water system, emptying and flushing the holding tanks, having the unit winterized if necessary. If you want the dealership to do these things for you make sure you agree on a price up front. You need to discuss any obvious repairs that may be required to get the unit ready to be sold. How much will the repairs cost and are the repairs paid up front or after the sale? You should take everything out of the RV before taking it to the dealership to be sold. If you have extra items that go with the RV, like an RV cover or other accessories ask the dealer to list the items and leave the information in the RV for potential buyers to see, but don’t physically leave these items in the RV while it's sitting on the lot.

Ask the dealer if they take precautions like putting a protective covering on the carpet to prevent dirt and stains from foot traffic. Is the RV going to be locked and secured when the dealership is closed? Will they keep the interior and exterior clean while it is on the lot, and if so are there additional charges for this? Ask them to explain any additional fees or monthly charges that may apply like cleaning, advertising and a pre-delivery inspection (PDI) fee after the sale. Any reputable RV dealership is going to do a PDI when the unit sells, and there will other charges like filling the propane cylinders and fuel tank. Do they start and run the RV on a regular basis? If the RV has a generator will they start and exercise it or is that something you will need to do? Can potential buyers test drive the unit if is a motorized RV, again you will need to keep insurance coverage on the unit. If they get an offer on the RV that is below the agreed upon price will they notify you with the offer for you to consider? These are just a few things to consider and review before putting the RV on consignment.

Remember the overall goal is to sell the RV in a timely manner. Things that help sell an RV, besides the type of RV it is and the floor plan are cleanliness, everything operating properly, no obvious damage, motivated sales people and of course the selling price. One way to motivate sales people is to offer them a sales spiff/incentive above and beyond their regular commission. Talk to the sales manager and see if this is something that can be arranged. Do what you are responsible for and let the dealership do what they are responsible for and the RV should sell in a reasonable time frame.

Happy RV Learning!
Mark Polk
RV Education 101

Learn about Mark's books, eBooks and DVDs at RVbookstore.com
Read more »


Copyright by Mark Polk owner of RV Education 101 – all rights reserved