The topic of RV batteries seems to come up a lot among RVers, and there is good reason for it. Did you know the average life for RV batteries with limited battery care and maintenance is only 2 to 3 years, and that 85% of all 12-volt batteries manufactured die before they should? That can get expensive, replacing two or more deep cycle batteries at a time.
Some of the reasons for these battery problems are undercharging, overcharging, not recharging a discharged battery in a timely manner, lack of maintenance, and a lack of understanding what is required to properly maintain batteries.
The #1 cause of battery failure is a condition called sulfation. When a battery is improperly charged, overcharged or undercharged, or allowed to self discharge small crystals of sulfuric acid from the battery’s electrolyte start to form on the charge plates. Over time this sulfate material cannot be converted back into active plate material and the battery is ruined.
This also occurs when a battery remains discharged for an extended period of time. These crystals act as a barrier, stopping the battery from ever accepting a full charge again regardless of how long you charge the battery. Once this happens, the power and longevity of the battery is severely reduced and your battery becomes one of the 85% that die before it should. Sulfation begins when a battery’s state of charge drops below 80%, or 12.4 volts.
I mentioned a moment ago that overcharging was one reason for batteries dying early. This is a common problem with RVs. The RV converter has a built in battery charger and most owners are under the impression that if you leave the RV plugged in when it is being stored it will keep the batteries topped off. Keeping the batteries topped off is extremely important, but the problem is many RV converter chargers provide a constant charge of about 13.5 volts which is too high for fully charged batteries. When this happens the electrolyte is boiled off resulting in an early death for the batteries.
ANOTHER PROBLEM IS NOT CHARGING the batteries at all when the RV is in short or long term storage or not recharging a discharged battery in a timely manner and letting it sit in that condition for extended periods of time. Both of these problems result in early battery death too.
Even for someone with a decent understanding of batteries and battery maintenance I had a few batteries that became statistics in the past. Then I discovered a way to prevent all of these battery related problems for good. It was a product that charges, maintains and conditions the batteries.
There are a few of these products on the market. The one I use is called The Battery Minder. What I mean by conditioning the battery is that the manufacturer of The Battery Minder has developed a simple but extremely effective circuitry that can safely dissolve the sulfation on the plates and restore much, if not all of the lost power. The reason The Battery Minder works so well is because it not only charges the battery, it maintains and desulfates the battery and will never overcharge the battery.
I’m not saying that you will never have to check the water levels or routinely inspect your batteries again, but this product will simplify your battery maintenance and extend the life of your batteries. It can even reverse sulfation on batteries that are already affected by this condition, if caught in time. It’s not very often that I endorse a product but The Battery Minder is one that I have been using for many years now, and through using it I have seen proven results.
When I’m not using the RV I hook the battery minder up and let it go. Through proper charging and maintenance you can easily double the life expectancy of your RV batteries.
If you would like to learn more about your deep cycle batteries check out our Deep Cycle Batteries DVD.
Thursday, May 26, 2011
Wednesday, January 12, 2011
What is an RV tow dolly?
A tow dolly is a two wheeled trailer used to transport the vehicle you are towing with the drive wheels off of the ground. Tow dollies are a good choice when the vehicle you are towing cannot be towed with all four wheels down or if the vehicle would require expensive modifications to tow with all four wheels down.
Selecting the Right Tow Dolly
Tow dollies are manufactured to accommodate a certain size vehicle. They must be able to handle the width and the weight of the towed vehicle. Like everything else tow dollies have maximum weight ratings too. When you purchase a tow dolly make sure that it is designed to support the weight and size of the towed vehicle. Some dollies are adjustable, meaning the same dolly can be set-up to tow different size vehicles, and others are made to tow just one size vehicle. Normally the width of the towed vehicle determines the size tow dolly. Check with the tow dolly manufacturer before making a purchase.
Note: Matching the wrong vehicle and tow dolly can result in damage to the towed vehicle.
Some tow dollies come equipped with brakes and others do not. Check with State or Province laws and the motor home chassis manufacturer about the requirement for a towed vehicle braking system based on the amount of weight you will be towing before you purchase a tow dolly.
Loading and Unloading the Tow Dolly
Before loading the vehicle unto the tow dolly make sure the tow dolly coupler is properly attached to the ball mount and that you are using the proper size hitch ball for the coupler. Use a safety pin or clip to secure the locked coupler. Attach the safety chains or cables making sure they are crossed, “X” to form a saddle that would prevent the coupler from contacting the road surface in the event of a separation. Plug the light cable in and check all of the lights for proper operation. Follow the tow dolly manufacturer instructions to determine the proper hitch ball height.
Note: Because tow dolly manufacturers have different operating instructions it is essential that you follow the tow dolly manufacturer’s specific instructions for proper loading, unloading, and vehicle tie down procedures.
Tow Dolly Pre-Trip Checklist
Perform these checks before each travel day.
* Check and adjust tire pressure to manufacturer recommendations. Check when tires are cold before traveling more than one mile.
* Check wheel lug nuts. Tighten to manufacturer specifications.
* Check that wheel hubs and bearings are properly adjusted and lubricated. Follow manufacturer instructions or have them checked by a repair facility.
* Check that all nuts and bolts are properly tightened. Do not use the dolly with any loose or damaged hardware.
* Check that the coupler is properly secured to the ball mount. Note: Follow manufacturer instructions for adjusting coupler tightness.
* Check the safety chains for proper attachment.
* Check all lights for proper operation.
* Check that the tow vehicle is properly secured to the tow dolly. Note: Follow manufacturer instructions.
* Make sure the towed vehicle parking brake is released after it is properly secured to the dolly.
* Stop after 10 miles of travel to check the tie down straps. Readjust as required. Check every 100 miles afterwards as a minimum.
* Do not attempt to back the tow dolly when vehicle is loaded on it!
Some Tow Dolly Towing Tips
* Perform all pre-trip checks before using the tow dolly.
* Make turns wider than you are accustomed to. Do not attempt to make sharp turns or U-turns. If you turn to sharply the vehicle you are towing can come in contact with the tow dolly fender causing damage to both the towed vehicle and dolly.
* Do not attempt to back the loaded tow dolly. Backing can damage the tow dolly and the towed vehicle.
* Allow a safe following distance, and anticipate all stops in advance.
* Do not speed, drive at a safe speed and keep in mind the dolly is wider than some vehicles towing it. Stay centered in your lane of traffic.
* If you experience excessive sway it may be caused by an improperly loaded tow dolly. Stop when it is safe, check and retighten the tie downs, or reload the vehicle. Check tie down straps every 100 miles at a minimum.
* The towed vehicle should always be facing forward on the dolly. A towed vehicle loaded from the rear can contribute to trailer sway.
* Never allow any passengers to ride in the towed vehicle.
Learn about Mark Polks extensive of helpful DVDs, books and eBooks at RVbookstore.com
Selecting the Right Tow Dolly
Tow dollies are manufactured to accommodate a certain size vehicle. They must be able to handle the width and the weight of the towed vehicle. Like everything else tow dollies have maximum weight ratings too. When you purchase a tow dolly make sure that it is designed to support the weight and size of the towed vehicle. Some dollies are adjustable, meaning the same dolly can be set-up to tow different size vehicles, and others are made to tow just one size vehicle. Normally the width of the towed vehicle determines the size tow dolly. Check with the tow dolly manufacturer before making a purchase.
Note: Matching the wrong vehicle and tow dolly can result in damage to the towed vehicle.
Some tow dollies come equipped with brakes and others do not. Check with State or Province laws and the motor home chassis manufacturer about the requirement for a towed vehicle braking system based on the amount of weight you will be towing before you purchase a tow dolly.
Loading and Unloading the Tow Dolly
Before loading the vehicle unto the tow dolly make sure the tow dolly coupler is properly attached to the ball mount and that you are using the proper size hitch ball for the coupler. Use a safety pin or clip to secure the locked coupler. Attach the safety chains or cables making sure they are crossed, “X” to form a saddle that would prevent the coupler from contacting the road surface in the event of a separation. Plug the light cable in and check all of the lights for proper operation. Follow the tow dolly manufacturer instructions to determine the proper hitch ball height.
Note: Because tow dolly manufacturers have different operating instructions it is essential that you follow the tow dolly manufacturer’s specific instructions for proper loading, unloading, and vehicle tie down procedures.
Tow Dolly Pre-Trip Checklist
Perform these checks before each travel day.
* Check and adjust tire pressure to manufacturer recommendations. Check when tires are cold before traveling more than one mile.
* Check wheel lug nuts. Tighten to manufacturer specifications.
* Check that wheel hubs and bearings are properly adjusted and lubricated. Follow manufacturer instructions or have them checked by a repair facility.
* Check that all nuts and bolts are properly tightened. Do not use the dolly with any loose or damaged hardware.
* Check that the coupler is properly secured to the ball mount. Note: Follow manufacturer instructions for adjusting coupler tightness.
* Check the safety chains for proper attachment.
* Check all lights for proper operation.
* Check that the tow vehicle is properly secured to the tow dolly. Note: Follow manufacturer instructions.
* Make sure the towed vehicle parking brake is released after it is properly secured to the dolly.
* Stop after 10 miles of travel to check the tie down straps. Readjust as required. Check every 100 miles afterwards as a minimum.
* Do not attempt to back the tow dolly when vehicle is loaded on it!
Some Tow Dolly Towing Tips
* Perform all pre-trip checks before using the tow dolly.
* Make turns wider than you are accustomed to. Do not attempt to make sharp turns or U-turns. If you turn to sharply the vehicle you are towing can come in contact with the tow dolly fender causing damage to both the towed vehicle and dolly.
* Do not attempt to back the loaded tow dolly. Backing can damage the tow dolly and the towed vehicle.
* Allow a safe following distance, and anticipate all stops in advance.
* Do not speed, drive at a safe speed and keep in mind the dolly is wider than some vehicles towing it. Stay centered in your lane of traffic.
* If you experience excessive sway it may be caused by an improperly loaded tow dolly. Stop when it is safe, check and retighten the tie downs, or reload the vehicle. Check tie down straps every 100 miles at a minimum.
* The towed vehicle should always be facing forward on the dolly. A towed vehicle loaded from the rear can contribute to trailer sway.
* Never allow any passengers to ride in the towed vehicle.
Learn about Mark Polks extensive of helpful DVDs, books and eBooks at RVbookstore.com
Wednesday, December 22, 2010
When hooked up, do I still need batteries in my RV?
Dear Mark,
For most RVs (I have a travel trailer) is the battery necessary to operate 12V appliances and accessories when you are plugged into shore power? In other words, does the AC current flow through the converter (converted to DC current) and then to the battery? or does the AC current flow through the converter and then directly to the 12V appliance and/or accessory?
For my trailer, if I'm plugged into shore power and I do not have the battery connected, only those appliances and accessories that operate on 120V will work (eg, air conditioner, microwave, etc). It would appear, therefore, that the battery is necessary even though I have shore power. (this was a surprise to me before I studied the AC / DC systems in a RV -- I initially thought that when plugged into shore power, my battery was not being used and all power consumption was coming directly from the AC current (converted to DC via the converter). I'm just trying to confirm that it's normal for only the 120V appliances/accessories to operate when (1) plugged into shore power and (2) battery is not connected.
Mark Says:
If the converter is operating properly you should not need the battery when it is plugged into electricity. The problem with not having a battery on the TT is the break-away system won't work when towing the RV. If you have no 12 volt devices operating (lights, fans, radio etc) when you are plugged into electricity (without a battery) something is probably wrong with the converter.
For most RVs (I have a travel trailer) is the battery necessary to operate 12V appliances and accessories when you are plugged into shore power? In other words, does the AC current flow through the converter (converted to DC current) and then to the battery? or does the AC current flow through the converter and then directly to the 12V appliance and/or accessory?
For my trailer, if I'm plugged into shore power and I do not have the battery connected, only those appliances and accessories that operate on 120V will work (eg, air conditioner, microwave, etc). It would appear, therefore, that the battery is necessary even though I have shore power. (this was a surprise to me before I studied the AC / DC systems in a RV -- I initially thought that when plugged into shore power, my battery was not being used and all power consumption was coming directly from the AC current (converted to DC via the converter). I'm just trying to confirm that it's normal for only the 120V appliances/accessories to operate when (1) plugged into shore power and (2) battery is not connected.
Mark Says:
If the converter is operating properly you should not need the battery when it is plugged into electricity. The problem with not having a battery on the TT is the break-away system won't work when towing the RV. If you have no 12 volt devices operating (lights, fans, radio etc) when you are plugged into electricity (without a battery) something is probably wrong with the converter.
Thursday, September 9, 2010
What to do with your RV in hurricane season
Do you live in an area that may be hit by a hurricane? If so, here are a few idea about what to do with your RV.
If a storm is on the way, moving the RV inland away from the storms projected path is the best scenario. If you can't do this yourself, perhaps you know someone who could do it for you before the storm's expected arrival. You could select a couple of campgrounds in advance that are inland, and depending on the storms trajectory move it to the most logical one. You would want to do this early enough so you can get a spot at the campground. Call a couple of local RV dealers and ask them for some good references of people who might be able to help you with moving the RV in the event of a hurricane. In this case you would want to pack the RV with food and clothing since you might need it for shelter after the storm.
If for any reason that scenario does not work and you must leave the trailer at your residence there are a few things I can think you should do:
Close all of the RV's windows and overhead roof vents.
Fill the propane but keep it turned off, and fill the fresh water holding tank with potable water. You may need this water after the storm. Do not fill the gray and black tank. You may need to use the RV after the storm and would want these tanks to be empty.
Make sure the battery is fully charged so you can use the 12-volt devices if you lose power after the storm is over.
Wind from a hurricane is unpredictable, but if the bulk of the wind is hitting against the front or rear of the RV, as opposed to the larger sides of the RV, there might be less damage or chance of serious damage. This translates to keeping one side of the RV close to the side or end of the house to help protect it from the high winds.
Avoid parking it in lower elevations. Water can flood low areas in a few hours during a bad storm, causing serious flooding.
If there are trees in the area that could damage the RV either move it to another location or keep the tree limbs trimmed.
Make sure any loose items in the area around the RV are secured prior to the storm.
As a precaution make sure your RV insurance is up to date and that it is covered in the event of a hurricane. The insurance company might offer some additional suggestions to protect the RV.
These are just a few ideas to help prepare your RV for a hurricane. You may want to ask the local RV dealers in the area if they have any suggestions, too.
Learn about Mark Polks extensive of helpful DVDs, books and eBooks at RVbookstore.com
If a storm is on the way, moving the RV inland away from the storms projected path is the best scenario. If you can't do this yourself, perhaps you know someone who could do it for you before the storm's expected arrival. You could select a couple of campgrounds in advance that are inland, and depending on the storms trajectory move it to the most logical one. You would want to do this early enough so you can get a spot at the campground. Call a couple of local RV dealers and ask them for some good references of people who might be able to help you with moving the RV in the event of a hurricane. In this case you would want to pack the RV with food and clothing since you might need it for shelter after the storm.
If for any reason that scenario does not work and you must leave the trailer at your residence there are a few things I can think you should do:
Close all of the RV's windows and overhead roof vents.
Fill the propane but keep it turned off, and fill the fresh water holding tank with potable water. You may need this water after the storm. Do not fill the gray and black tank. You may need to use the RV after the storm and would want these tanks to be empty.
Make sure the battery is fully charged so you can use the 12-volt devices if you lose power after the storm is over.
Wind from a hurricane is unpredictable, but if the bulk of the wind is hitting against the front or rear of the RV, as opposed to the larger sides of the RV, there might be less damage or chance of serious damage. This translates to keeping one side of the RV close to the side or end of the house to help protect it from the high winds.
Avoid parking it in lower elevations. Water can flood low areas in a few hours during a bad storm, causing serious flooding.
If there are trees in the area that could damage the RV either move it to another location or keep the tree limbs trimmed.
Make sure any loose items in the area around the RV are secured prior to the storm.
As a precaution make sure your RV insurance is up to date and that it is covered in the event of a hurricane. The insurance company might offer some additional suggestions to protect the RV.
These are just a few ideas to help prepare your RV for a hurricane. You may want to ask the local RV dealers in the area if they have any suggestions, too.
Learn about Mark Polks extensive of helpful DVDs, books and eBooks at RVbookstore.com
Monday, July 26, 2010
Be careful towing downhill: that's when accidents happen
Eighty percent of all towing related accidents happen when you're traveling downhill. It takes approximately three times longer to stop than if you were on a flat surface and the greater your speed the greater the stopping distance required. Here are a few tips for towing on downgrades.
Downshift on downgrades to lessen the braking action required. Reduce your speed. Remember that trailer sway is more likely to occur when descending inclines. On steep or long downgrades reduce gears and avoid prolonged brake use on the tow vehicle. The brakes can easily overheat and begin to fade. Use the vehicle brakes in intervals.
If the trailer becomes unstable when descending an incline and the trailer starts to sway, reduce your speed, avoid using the vehicle brakes, and manually activate the trailer brakes to regain control.
Do not travel above the posted speed limit on downgrades. Leave plenty of room between you and the vehicle in front of you.
Downshift on downgrades to lessen the braking action required. Reduce your speed. Remember that trailer sway is more likely to occur when descending inclines. On steep or long downgrades reduce gears and avoid prolonged brake use on the tow vehicle. The brakes can easily overheat and begin to fade. Use the vehicle brakes in intervals.
If the trailer becomes unstable when descending an incline and the trailer starts to sway, reduce your speed, avoid using the vehicle brakes, and manually activate the trailer brakes to regain control.
Do not travel above the posted speed limit on downgrades. Leave plenty of room between you and the vehicle in front of you.
Friday, April 2, 2010
What you need to know about RV extended warranties
Someone e-mailed me recently and wanted to know my thoughts on RV extended service plans. I replied that I thought extended service plans offered great protection as long as you understand a little about them and how they work. When you are doing the finance paperwork on your RV most RV dealers will offer you some type of extended service plan that you can purchase. Before you agree to purchase a plan make sure you understand all of your options. You should not be pressured into buying an extended service contract.
If you buy a new RV and purchase an extended service plan that covers both the coach and the chassis, the plan would take over the day after all of the original factory warranties expire. For example, if you purchase a seven year extended service plan and the motorhome has a one year warranty on the coach and a three year warranty on the chassis the service plan would be in affect for six years after the coach warranty expires and for four additional years after the chassis warranty expires.
The advantage of purchasing the plan when the RV is new is that it will be less expensive for a new unit as opposed to a used unit. Most plans can be purchased anytime up until the factory warranties expire if you don’t purchase the plan when you initially buy the RV. Some extended service plans will offer coverage on used units that meet the plans criteria if you purchase the plan when you buy the used unit. Coverage on a used unit will cost more. It is usually based on the age of the unit and the mileage if it’s a motorized RV.
I mentioned if you buy coverage for the coach and the chassis. That’s because most of these service plans offer different levels of coverage. You may only want additional coverage on the coach portion or on the chassis portion. In addition to different levels of coverage, plans are available for different terms.
MAKE SURE YOU READ and understand the extent and time period of coverage before signing any agreements. If you don’t understand something, ask to have it explained to you. You will also want to make sure that the company offering the plan is reputable and will be acknowledged by other RV dealers and RV repair centers. It should offer coverage in all of the USA and/or Canada. If you plan to travel outside your country of origin make sure the coverage is still available.
You will also want to check on how a claim is paid. I have seen cases where you pay for the repairs up front and then get reimbursed when you send in a copy of the service order or repair bill. If the repair facility agrees to file the claim most plans only require that you call for approval before any repairs are made. A good plan should be transferable if you sell your RV, it should be renewable so you can extend the coverage and it should offer a pro rated refund if coverage is terminated during the term of the contract.
Pricing for these plans will be based on several factors. I have already mentioned some; the length of the plan, the extent of coverage, if the RV is new or used, the age and mileage, and the deductible. The deductible can range from $0 to over $200. This is not bad considering a $500 or $1,000 average repair bill if an appliance fails. Some items on the RV, like slideouts and entertainment systems may not be covered unless you pay an additional surcharge. Make sure you understand what these items are and if you want them to be covered by the plan.
Do not be pressured into purchasing a plan. Ask your RV dealer to give you a price on the plan they have to offer and then you can shop around and compare pricing for extended service plans. Just make sure the plans you are comparing offer similar coverage. Research and know in advance what you plan to do about an extended service plan before you go in to sign the finance paperwork.
Learn more from businesses that offer extended warranties.
If you buy a new RV and purchase an extended service plan that covers both the coach and the chassis, the plan would take over the day after all of the original factory warranties expire. For example, if you purchase a seven year extended service plan and the motorhome has a one year warranty on the coach and a three year warranty on the chassis the service plan would be in affect for six years after the coach warranty expires and for four additional years after the chassis warranty expires.
The advantage of purchasing the plan when the RV is new is that it will be less expensive for a new unit as opposed to a used unit. Most plans can be purchased anytime up until the factory warranties expire if you don’t purchase the plan when you initially buy the RV. Some extended service plans will offer coverage on used units that meet the plans criteria if you purchase the plan when you buy the used unit. Coverage on a used unit will cost more. It is usually based on the age of the unit and the mileage if it’s a motorized RV.
I mentioned if you buy coverage for the coach and the chassis. That’s because most of these service plans offer different levels of coverage. You may only want additional coverage on the coach portion or on the chassis portion. In addition to different levels of coverage, plans are available for different terms.
MAKE SURE YOU READ and understand the extent and time period of coverage before signing any agreements. If you don’t understand something, ask to have it explained to you. You will also want to make sure that the company offering the plan is reputable and will be acknowledged by other RV dealers and RV repair centers. It should offer coverage in all of the USA and/or Canada. If you plan to travel outside your country of origin make sure the coverage is still available.
You will also want to check on how a claim is paid. I have seen cases where you pay for the repairs up front and then get reimbursed when you send in a copy of the service order or repair bill. If the repair facility agrees to file the claim most plans only require that you call for approval before any repairs are made. A good plan should be transferable if you sell your RV, it should be renewable so you can extend the coverage and it should offer a pro rated refund if coverage is terminated during the term of the contract.
Pricing for these plans will be based on several factors. I have already mentioned some; the length of the plan, the extent of coverage, if the RV is new or used, the age and mileage, and the deductible. The deductible can range from $0 to over $200. This is not bad considering a $500 or $1,000 average repair bill if an appliance fails. Some items on the RV, like slideouts and entertainment systems may not be covered unless you pay an additional surcharge. Make sure you understand what these items are and if you want them to be covered by the plan.
Do not be pressured into purchasing a plan. Ask your RV dealer to give you a price on the plan they have to offer and then you can shop around and compare pricing for extended service plans. Just make sure the plans you are comparing offer similar coverage. Research and know in advance what you plan to do about an extended service plan before you go in to sign the finance paperwork.
Learn more from businesses that offer extended warranties.
Thursday, February 25, 2010
The most common RV repairs and why you need a checklist
The two most common repairs to an RV are the steps and the TV antenna. Damage to RV steps and TV antennas occur frequently and can be costly to repair. The main reason is because RVers forget to do a walk around of their unit before leaving on a trip or leaving the campground. The good news is both of these common repairs can be avoided by following a simple pre-trip checklist before heading out in your RV.
Regardless of the type of RV you own you need to get in the habit of making these pre-trip checks every time you use your RV. Taking a few minutes to complete these simple checks can save you time and money for unnecessary repairs to your RV. Here is a good pre-trip checklist.
Outside of your RV
* Check and adjust the air pressure in all tires. Always check the tires when they are cold, before traveling more than one mile.
* Check the lug nuts on the wheels. Discoloration and stains around lug nuts indicate they may be loose.
* Make sure all items in the storage compartments are secure. Lock all outside compartments.
* Check the bike rack and bikes for secure mounting if applicable.
* Make sure the power cord and water hose, and the sewer hose are disconnected and properly stored.
* Make sure all slide outs are in and slide out travel locks are securely in place.
* Make sure the TV antenna and / or satellite are down and stowed in the proper position for traveling.
* Check the awning. Make sure that it is securely stored and all travel locks and knobs are tight and locked.
* Raise all stabilizer jacks or hydraulic leveling jacks.
* Look under the RV for any indications of leaks (motorized) or anything out of the ordinary.
* Stow or retract the steps.
* Fill the fresh water holding tank with enough potable water to get to your destination.
* Check and secure the cap on the sewer outlet.
* Turn all LP gas appliances off and turn the gas supply off at the tank or bottles.
* Double check all hitch work on towable RV's and on vehicles being towed behind motor homes.
* Check all fluid levels for motorized RV's and tow vehicles.
* Remove and store wheel chocks and any type of leveling blocks.
* Check all running lights, turn signals, brake lights and headlights on the RV and tow vehicle.
* Check for an up to date inspection or emission sticker and license plates.
* Check trailer brakes for proper operation.
* Make one last walk around the outside and check for anything you may have overlooked.
Inside of your RV
* Walk through the entire RV and secure all loose items that could move, fall or get damaged while traveling.
* Turn off all appliances gas & electric. Turn off all pilot lights.
* Close all roof vents
* Close all doors, drawers and cabinets
* Check for anything in the refrigerator that could spill. Lock the refrigerator and freezer doors.
* Turn off the 12-volt water pump.
* Close the range top cover.
* Turn off all 12-volt lights and accessories that could drain the auxiliary battery. Don't forget the TV antenna booster.
* Close the windows and secure blinds.
* Secure any large items such as TVs and computers that might move or fall while traveling.
* All weight in the RV should be distributed evenly. Adjust your mirrors and seat and hit the road.
This checklist may not be all-inclusive, but it's a good start. You can add to this list and tailor it to your specific type of RV. The most important thing to remember is to use this checklist every time you use your RV. It's easy to forget something without a reminder. I always do one last walk around of the RV just before pulling out. You'll be amazed at what you may have missed the first time around.
Looking for a more thorough checklist? Mark has one available for instant download. Click here to get it.
Regardless of the type of RV you own you need to get in the habit of making these pre-trip checks every time you use your RV. Taking a few minutes to complete these simple checks can save you time and money for unnecessary repairs to your RV. Here is a good pre-trip checklist.
Outside of your RV
* Check and adjust the air pressure in all tires. Always check the tires when they are cold, before traveling more than one mile.
* Check the lug nuts on the wheels. Discoloration and stains around lug nuts indicate they may be loose.
* Make sure all items in the storage compartments are secure. Lock all outside compartments.
* Check the bike rack and bikes for secure mounting if applicable.
* Make sure the power cord and water hose, and the sewer hose are disconnected and properly stored.
* Make sure all slide outs are in and slide out travel locks are securely in place.
* Make sure the TV antenna and / or satellite are down and stowed in the proper position for traveling.
* Check the awning. Make sure that it is securely stored and all travel locks and knobs are tight and locked.
* Raise all stabilizer jacks or hydraulic leveling jacks.
* Look under the RV for any indications of leaks (motorized) or anything out of the ordinary.
* Stow or retract the steps.
* Fill the fresh water holding tank with enough potable water to get to your destination.
* Check and secure the cap on the sewer outlet.
* Turn all LP gas appliances off and turn the gas supply off at the tank or bottles.
* Double check all hitch work on towable RV's and on vehicles being towed behind motor homes.
* Check all fluid levels for motorized RV's and tow vehicles.
* Remove and store wheel chocks and any type of leveling blocks.
* Check all running lights, turn signals, brake lights and headlights on the RV and tow vehicle.
* Check for an up to date inspection or emission sticker and license plates.
* Check trailer brakes for proper operation.
* Make one last walk around the outside and check for anything you may have overlooked.
Inside of your RV
* Walk through the entire RV and secure all loose items that could move, fall or get damaged while traveling.
* Turn off all appliances gas & electric. Turn off all pilot lights.
* Close all roof vents
* Close all doors, drawers and cabinets
* Check for anything in the refrigerator that could spill. Lock the refrigerator and freezer doors.
* Turn off the 12-volt water pump.
* Close the range top cover.
* Turn off all 12-volt lights and accessories that could drain the auxiliary battery. Don't forget the TV antenna booster.
* Close the windows and secure blinds.
* Secure any large items such as TVs and computers that might move or fall while traveling.
* All weight in the RV should be distributed evenly. Adjust your mirrors and seat and hit the road.
This checklist may not be all-inclusive, but it's a good start. You can add to this list and tailor it to your specific type of RV. The most important thing to remember is to use this checklist every time you use your RV. It's easy to forget something without a reminder. I always do one last walk around of the RV just before pulling out. You'll be amazed at what you may have missed the first time around.
Looking for a more thorough checklist? Mark has one available for instant download. Click here to get it.
Subscribe to:
Posts (Atom)

